🔆 EShine 12-Inch LED Dimmable Under Cabinet Lighting Kit, Hand Wave Activated - Touchless Dimming Control - Deluxe Kit, Cool White (6000K) Review

Glad I ordered "cold white" instead of warm colors. Installation was easy. I made some 3/8" holes in my old cabinets for wiring. The light level can vary from about 10 percent to an intense full level. And the sensor remembers where it was installed when it's turned off.

Amazing. Period. Bright white lighting (I have the 6000K cool white option), easy to install, easy to use and overall great! This is my fourth set of LED under cabinet lights I've bought from EShine and the story has been the same every time. I have no doubts that I will be buying more sets in the future. Due to the slightly unusual installation location in our kitchen, I had to purchase a separate power cord extension and a pair of 6" patch cords. But they were perfect and the whole…

I bought 6 sets in total, both 6 panel and 12 panel versions of these for my house, housewarming gifts from friends and for my office. These lamps are the best in the world as they consume little energy but have high performance. They are very easy to install and pretty impressive. All my orders arrived on time and without defects. I've seen other under counter lighting kits that are much more expensive and don't come close to this one. Here are my general comments: 1. Very approachable2. super

4.5 stars. We bought these lights to put above and below our kitchen cabinets because I felt like I lacked light when cooking. They are easy to assemble and can be attached to desired locations with screws or adhesive strips. I would like two longer wires instead of one because I needed a second wire to go through the cabinets to cover the entire area (top and bottom) and I ordered it separately. The hand sensor on the main light works fine, but does not always react. Please note that if you…

Simple? It is not easy. It's SUPER EASY! I assembled this lighting kit and got it up and running in an hour and a half (had to drill a hole). I used double sided tape. I cleaned the bottom of some very old cabinets with 409 and they stuck to it like glue! I got warm white and they made the kitchen countertops look amazing! If you also need lighting for small areas, you can use Lightkiwi lights with it. I need a 6 inch flashlight and used one from Lightkiwi and connected with the cable that came

My application was for glass door cabinets in the butlers pantry. I needed 4 for the interior to shine through the crystal and glass shelves and 4 for the bottom to shine on the counter. The cable on the PSU was long enough to reach the top of the 42-inch case, but there wasn't a long enough connection cable to reach the top. this was necessary because the socket was upstairs by the cupboards - the first light had to be downstairs and the last one up again. I connected two jumpers together (and

I checked every LED before installing it. All 12 light strips worked perfectly. Love the fact that they give you different connection options (11 wires, 11 connectors, lots of zip ties, double sided tape, screws). The light is nice and bright. But on the second day I waved my hand to turn it on and the lights flickered and 4 of them wouldn't come on. All LEDs were linearly connected. 4th, 5th, 6th, 7th, 8th etc. Nos. 1, 4, 7 and 8 turned on but 2, 3, 5 and 6 were NOT happy. I was able to get a…

We replaced our cabinets and installed lights while we went on. As a result, we only have one wire in one of the cabinets. All other cables run between cabinets, in fillers, and under cabinets. We installed an outlet inside and at the top of the cabinet. This served us as a food source. We ran a part in parallel, which saved a lot of wire. One thing to note: make sure you have enough room at the end of the world to insert the plug or cord. We have ordered additional cables and various…

Installation is easy, but as with anything, location is key. I used the supplied self-adhesive pre-positioning/installation strips and when I was satisfied I went back and screwed them in place. The included #4 x 1/2" screws were too long for my cabinet base. I purchased #4 x 5/16" self-tapping screws that worked great. (cheap/thin chipboard base) This order has 12 light strips, one of which contains an on/off/dimming sensor that needs to be powered first to control the others. Also, the sensor