Header banner
Revain logoHome Page
cnc aluminum φ 39mm clip ons handlebar for nightster iron 883 sportster xl883, modified cafe racer [0° tilt] logo

CNC Aluminum Φ 39mm Clip ons Handlebar for Nightster Iron 883 SPORTSTER XL883, Modified Cafe Racer [0° Tilt] Review

7

·

Very good

Revainrating 4 out of 5  
Rating 
4.1
🛺 Motorcycle Parts, 🏍️ Motorcycle & Powersports

View on AmazonView on ЯM

Media

(4)
img 1 attached to CNC Aluminum Φ 39mm Clip ons Handlebar for Nightster Iron 883 SPORTSTER XL883, Modified Cafe Racer [0° Tilt]
img 2 attached to CNC Aluminum Φ 39mm Clip ons Handlebar for Nightster Iron 883 SPORTSTER XL883, Modified Cafe Racer [0° Tilt]
img 3 attached to CNC Aluminum Φ 39mm Clip ons Handlebar for Nightster Iron 883 SPORTSTER XL883, Modified Cafe Racer [0° Tilt]
img 4 attached to CNC Aluminum Φ 39mm Clip ons Handlebar for Nightster Iron 883 SPORTSTER XL883, Modified Cafe Racer [0° Tilt]

Description of CNC Aluminum Φ 39mm Clip ons Handlebar for Nightster Iron 883 SPORTSTER XL883, Modified Cafe Racer [0° Tilt]

1.Fit on the upper portion of the fork tubes diameter 39mm,Clamp height: 40mm, Tilt 0 Degrees. 2.Machined out of 7075-T6 aluminum,Bars diameter: approx 1 inch (1") ,bars Length: 300mm(12") length. 3.Fits 2014-later XL883N, XL1200C, XL1200NS and 2007-2015 XL1200X models with 39mm forks.Does not fit with Heated Hand Grips. 4.It is an economical replacement handlebar with amazing strength,Clean lines to match modern sportbikes. 5.Close to the prototype design,More suitable for your motorcycle,No instructions included.

Reviews

Global ratings 7
  • 5
    5
  • 4
    0
  • 3
    1
  • 2
    0
  • 1
    1

Type of review

Revainrating 5 out of 5

Nice finish, good quality

I needed 1" bars but couldn't find them with 41mm clamps. Bought these and a set of 41mm bars with 7/8" bars to get what I need.

Pros
  • Easy to install
Cons
  • Only available in black

Revainrating 5 out of 5

Very few changes are required.

motorcycle turn signal hub needs minor modification to fit as factory. In addition, the product is very good, easy to install, good quality

Pros
  • Cool
Cons
  • No automatic

Revainrating 5 out of 5

Looks good Fits well Appears well built and strong

Looks great Fits well Appears well built and strong. from my old bars to these. Apparently my old coating on the bars made them a little over 1 inch thick.

Pros
  • GOLS certified
Cons
  • Working speed

Revainrating 1 out of 5

Do not buy! Dangerous!

VERY DANGEROUS! When I installed the bars I noticed that the bars were still moving, so I tightened the first screw a quarter turn and felt it was completely loose. I'm so glad I didn't ride because other studs did the same. The metal is too soft for the vibrations felt by the steering wheel. DO NOT BUY THESE!

Pros
  • Makes you happy
Cons
  • Expensive

Revainrating 3 out of 5

Be very careful when tightening

One fell off the bracket and the second blew off. There are very few threads involved and being aluminum they are very easy to remove. There aren't many cheap clip-on options that fit Harleys. In the end I settled on a low riding position and club handlebars to get the look I wanted. I was too scared they would slip in heavy riding conditions.

Pros
  • Sturdy construction
Cons
  • I don't remember but there was something

Revainrating 5 out of 5

The clips are of very good quality so be it.

Very good quality clips, and would still be the case if they cost >$100. The handlebar end mirror cutouts and CNC machined aluminum were actually stronger than the stock handlebars on my Iron 883. There were no installation issues and the butt controls fit perfectly, in my case I didn't have to drill any holes for the wiring harness in the steering wheel . .

Pros
  • Everything is fine!
Cons
  • too blunt

Revainrating 5 out of 5

The bars shrink to 7/8 " in the clamp and will work with any clamp that accepts 7/8 " bars.

I just bought them for bars. (Replacement bars are $20 each, and with this kit I could get two 1" bars for $35). ", but reduced to 7/8" at the clamping point. (I have a 2002 Honda Shadow 1100. This bike has 41mm tubes and requires 41mm clamps. Just buy both kits, 41mm clamps with 7/8" bars and 39mm Clamps with 1" handlebars (This is cheaper than looking for 41mm forks with 1" rods. If I'm lucky I might sell those 7/8" rods and 39mm forks to someone else. )

Pros
  • good thing
Cons
  • expensive insurance