Header banner
Revain logoHome Page
partsam rectangular rectangle clearance motorhome logo

Partsam Rectangular Rectangle Clearance Motorhome Review

4

·

Very good

Revainrating 4 out of 5  
Rating 
4.0
💡 Car Lighting Assemblies & Accessories, 💡 Car Lights & Lighting Accessories

View on AmazonView on ЯM

Media

(4)
img 1 attached to Partsam Rectangular Rectangle Clearance Motorhome
img 2 attached to Partsam Rectangular Rectangle Clearance Motorhome
img 3 attached to Partsam Rectangular Rectangle Clearance Motorhome
img 4 attached to Partsam Rectangular Rectangle Clearance Motorhome

Details

Light Source TypeLED
BrandPartsam
PositionRear
Lens MaterialPolycarbonate
Voltage12 Volts

Description of Partsam Rectangular Rectangle Clearance Motorhome

Package includes 12Pcs 4 Inch Oval Led Marker Lights 10 LED Diodes (7 Red + 5 Amber), Screws are included for mounting. Red on the side at the rear corner and amber at the side on the front corner. You can also have lights on the top edge both on the sides and on the front and back of the campers;. These marker lights includes 10 LED diodes each. LEDs are brighter and light faster, draw less current and generate less heat than incandescents; Note: These oval lights are removable. Please snap off the lens to install. When you put the screws in, please do not tight them to much or the lens will be cracked. After you snap them on, please kindly put a little silicone or some clear RTV all across the gap to help seal it just in case it leaks into the light or where the wires are;. Dimensions: 4" x 2" x 1" with 3" hole distance approximately. These oval marker lights are the exact same size as the light on a camper; Hardwired with 2 wires: Black is ground and red is hot;. Installation: for these oval clearance lights, the wires come out of the side instead of the middle. We truly get some suggestions to install them from our brilliant customers: 1. use a dremel to cut a grove to get the wires to the middle; 2. use a little of the tape putty on the main body, then it lays right in there and stay flush with the surface; 3. please shim the light out slightly to allow the wires to run to the hole without smashing it; 4. drill a hole in frame of trailer to install;. Warranty: These oval led lights are universal for 12V DC vehicles like RV CAMPER TRAILER Trucks Motorhome Tractor Motorcycle Utility vehicle fifth wheel toyhauler Pickups SUV van Caravan and Boat Lorry Bus etc. 1 Year Warranty Guaranteed;.

Reviews

Global ratings 4
  • 5
    1
  • 4
    2
  • 3
    1
  • 2
    0
  • 1
    0

Type of review

Revainrating 3 out of 5

The light is bright and looks beautiful.

Came with all the parts needed to replace all the marker lights on my fifth wheel. The light is bright and looks beautiful.

Pros
  • Marker light assembly
Cons
  • Some bugs

Revainrating 5 out of 5

Happiness for my camper

Easy installation. Just power up the circuit so the wires are in the correct orientation as they are both black. I replaced the steady lights on my RV and they are spot on. It doesn't seem any worse than the original. And brighter than the original. Happy I bought.

Pros
  • Lighting and accessories
Cons
  • Reliability

Revainrating 4 out of 5

Nice and bright in lamps and lighting accessories

Overall these are nice headlights. Installed them on my caravan as incandescent bulbs were not suitable for the daytime sun. because I like to drive with lights on during the day when I'm towing a trailer. They can now be seen in daylight, very bright! Now the reason for the 4 star rating is that moisture builds up on the inside of the lenses.

Pros
  • Side markers complete
Cons
  • So-so

Revainrating 4 out of 5

The new lights have a red and black wire.

New lights have a red and black wire to connect to your wires. Plug one in and check the polarity on your tag. There is a problem with the design. The wires come out of the bottom corner. In most old conventional lightbulbs, the wires come out of the middle. There should be a groove just above where the wires come out the back of the light to allow the wires to be routed to the center cutout, otherwise the light will not lay flat. This way you can continue to use the existing holes in your old…

Pros
  • Automotive
Cons
  • Blank