🔦 STBTECH 110V Under Cabinet Light,15.7in LED Strip Lighting with 6ft US Plug Cable,Switch in The Middle,Easy Magnetic Installation,Reading Desk Lamp for Kitchen/Work Table - Naturally White 4000K Review

Headlights are lighter than a cable, magnets and self-adhesive metal pads are included. The heat from the lamp softened the adhesive on the pad, causing it to fall off several times. Now attached to an old metal lamp while looking for mounting screw holes. Enough light to illuminate a tool shelf, not a shop.

Great color (6000K) and very bright. They are thin and light in weight. The mounting hardware included in the kit worked great for me. A NOTICE. These lights have a true on/off toggle switch on the cord, meaning they can be switched on and off with a switching voltage of 110V. They work with Alexa, remote switches, etc. Many lights like this one sold at Revain don't work on 110v switching voltage, instead you have to press the power button on the light each time.

I bought these lights to install under kitchen cabinets. Installation was easy, I used magnetic mounts. This way I can easily move them to different places. The lighting is bright, if necessary it can be dimmed or switched to a softer light. We use ours every day and love them. An added feature, since they are USB powered, you can connect them to a rechargeable battery pack used to charge cell phones and tablets in the event of a power outage. Perfect tension and light for hours.

I was looking for a simple plug in LED under cabinet light for my garage cabinets at 5000-6000 which was proving to be more difficult to find than I was expecting. I chose these lamps and was pleasantly surprised. The flashlights come pre-installed with either double-sided tape or a small rare earth magnet. 6 foot cable with standard plug. It was easy to install. Attach to cabinets, plug in and turn on. I ran them for hours and they didn't get hot and there weren't any issues with the LEDs or…

I outwitted myself installing a 5 foot shelf around my sewing table. You see I bought a very bright LED panel and hung it above the table to compensate for the old eyes. That is, until I hung a 5 foot long and 1 foot deep shelf over this table and blocked some of that wonderfully bright light. Enter this little gem. I snap it onto the metal brackets holding up this ugly shelf and now I can thread my car through it again. If you have old eyes like me and need some good, bright work lighting, try

I outwitted myself installing a 5ft shelf around my sewing workbench. You see I bought a very bright LED panel and hung it above the table to compensate for the old eyes. That is, until I hung a 5 foot long and 1 foot deep shelf over this table and blocked some of that wonderfully bright light. Enter this little gem. I snap it onto the metal brackets holding up this ugly shelf and now I can thread my car through it again. If you have old eyes like me and need some good, bright work lighting…

What a great purchase at this price! These LED lights meet all my needs. They're encased in a white plastic case, which I like because I hate seeing LED dots. It's nothing fancy, no dimmer, no tone controls, just an on/off switch, but at this price you can't beat it. These lights are very bright and brighten up my dressing table with a cool tone and modern look. I didn't use the magnets that came with it (because they're too wide for the edge of my mirror) but it's definitely a brilliant idea…

It's supposed to be 17 inches long but when you unplug the end caps and about a half inch on each side the light doesn't come on. This is closer to 14 inches of actual light. I placed it over the sink so I didn't have to use magnets to hold it in place. I took them out and screwed them to the ceiling above the sink about 3 1/2 to 4 feet from the sink. On it was a photo of a lamp mounted over a sink. It is great for placing under a cabinet that is close to the counter but no higher than 2ft…

I used this to fix marquee on my robotron arcade machine. The original ballast transformer failed after 38 years and a replacement cost nearly $30. This LED strip is just the right length and half the price. The magnet mounts were already installed so all I had to do was place them on top of the metal plate that the old fluorescent tube was on and cut/connect the power supply to the original wiring harness. I left the original mount in place in case I ever need a true restore, but for now I…