🪚 Hole Saws & Accessories
2 Review
1-3/8-Inch depth. Use standard or SDS shank arbors. Works in rotary and SDS hammer mode, works forward and reverse. Drilling a hole through concrete block takes less than 7 seconds. Cuts brick, concrete block, fiber cement siding & backer board, stucco, old plaster.
2 Review
The best cutting result for drilling in asphalt, brick, concrete, dry wall, marble, tile, wood, composite, etc; Carbide Tip Pilot Drill bit is required. Fit arbors with 5/8-18 UNF Thread; 2-1/4“ Cut-Depth allows for easily cutting through thick or layered building materials in one pass. Quality Carbide Teeth have high hardness, outstanding wear…
Read more about this product
2 Review
Bonded Diamond Grit: Electroplate bonded diamonds for optimum diamond life. Nickel Plated: Reduces bit friction and heat build-up and inhibits rust. Grooved Tip Edge: Provides maximum surface area & increases water "churn" for tip lubrication. Tip Lubrication Hole: Provides optimum tip lubrication by allowing water flow in and out of bit. Core…
Read more about this product
2 Review
A cost effective solution for cutting nail imbedded wood, or wood and metal combination, reinforced concrete and fiberglass. Leaves high quality surface finish on entry and exit and provides a smooth cut when cutting traditional lathe and plaster. Tungsten carbide tipped teeth for outstanding cutting performance and product durability. Will cut nail…
Read more about this product
2 Review
Patent Pending tooth set design optimized to remove material faster. Attached arbor and pilot drill included. New side slot increased leverage for faster, easier slug removal. New exterior red coating reduces side wall friction for efficient cutting. Heavy duty .050 side wall for greater stability.
2 Review
1.Different Size: 16mm/0.62'',18.5mm/0.73'',20mm/0.78'',25mm/0.98'',30mm/1.18'', interval for each specification), total length 65mm/2.55''. 2.Cutting edge strictly symmetrical: Surface anti-rust treatment, smoother drilling and chipping.beneficial and efficient cutting, avoid offset drilling. Big space for chip removal, big space for chip removal, the…
Read more about this product
2 Review
SIZE - 19mmDrilling Diameter, 5.5mm(0.22-inch) Shank Diameter. DIAMOND COATED - Diamond coating enhances the drilling speed, which makes the bit more sharp. NICKEL PLATED SURFACE - Nickel plating surface can extend the service life and enhance the surface corrosion resistance. SPECIAL DESIGN - Side open can remove the waste to keep the drill bit clean…
Read more about this product
2 Review
Traditional narrow openings on the side wall; M42 cobalt hole saw cutter. 4/6 variable tooth; thin kerf design for faster cutting and prolongs battery life when uysed on coredless tools; 1-7/8" (48mm) cutting depth; 3/16" (5mm) thick heavy-duty backing plate eliminates need for drive plate. Shock resistant teeth, resists tooth slippage, less vibration…
Read more about this product
2 Review
This item is Vermont American 18318 Carbon Steel Hole Saw, 1-1/8". Used for Power Tool Accessories, Drill Bits & Accessories. The produt is manufactured in China. Package weight:3.2 lb.
2 Review
Drilling Diameter: 60mm / 2.36-inch; Total Length: 83mm / 3.27-inch. Material: Diamond coating maximizes performance and retains a sharper cutting edge. Application: Ideal tool for cutting accurate holes in some materials such as stone and concrete. Note: Please remember to use at a low speed and work with coolant when processing. Package Content: 1pc x…
Read more about this product
2 Review
The best cutting result for drilling in asphalt, brick, concrete, dry wall, marble, tile, wood, composite, etc; Carbide Tip Pilot Drill bit is required. Fit arbors with 5/8-18 UNF Thread; 2-1/4“ Cut-Depth allows for easily cutting through thick or layered building materials in one pass. Quality Carbide Teeth have high hardness, outstanding wear…
Read more about this product
2 Review
Ideal for cutting stainless and high alloy steels, non-ferrous light metals and reinforced fabrics at a much faster speed than bi-metal hole saws. Tough tungsten carbide tipped teeth have a positive cutting angle which provide fast and efficient removal of chips and swarf. Ideal for production cutting and particularly suitable for use in drills with…
Read more about this product
2 Review
Cut ceramic tiles, wood, MDF, Trespa, plastics, plasterboard, soft bricks, lime bricks and more. Long lasting construction grade carbide to provide a 10x longer cutting life. Secured tooth technology to prevent any breakage during impact with hard materials. Fast lock in one click, fast drill in all conditions, fast bore enlargement thanks to the center…
Read more about this product
2 Review
New Rapid Core eject holes saws allow you drop out the core at the touch of a button. Made with tough bi-metal steel. Variable tooth pitch guarantees a fast and clean cut through all thicknesses. Cutting depth of up to 1-7/8".
2 Review
Great Performance: Opening neat, smooth, no broken edges, no tremor phenomenon, chip easily. Excellent for making clean and accurate hole on glass or tile etc. Diamond Coated: It is diamond coated and perfect for drilling a hole. Should use with coolant like water to prevent diamond layer from burning and expand the drilling life. Small incision…
Read more about this product
2 Review
Ideal for cutting stainless and high alloy steels, non-ferrous light metals and reinforced fabrics at a much faster speed than bi-metal hole saws. Tough tungsten carbide tipped teeth have a positive cutting angle which provide fast and efficient removal of chips and swarf. Ideal for production cutting and particularly suitable for use in drills with…
Read more about this product
2 Review
Product Type: Tools. Package Dimensions: 5.6 L x 16 W x 18.2 H (centimeters). Country of Origin: China. Package Weight: 0.603 kilograms.
2 Review
Special Tungsten Carbide Teeth with One Piece Construction. Removable Ejector Spring, Replaceable Pilot Pin and comes with Safety Collar Stop. Maximum cutting depth of 1-Inch and can cut thick steel plate and pipe, ductile, iron, aluminum, copper, cast iron, stainless steel, FRP(fiberglass) hardboard and plastics (PVC and Conduit). Maximum cutting depth…
Read more about this product
2 Review
Hole Saw Blade for Drilling Cutting Wood Plastic, BI-Metal Heavy Duty Steel. This Hole Saw Drill Bit is designed for wood / plastic cutting. It is made of Bi-Metal Heavy Duty Steel, Durable and Rust-proof. 1 inch hole diameter for drilling or cutting 1” diameter holes through Wood or Plastic. Non-binding clean edge design make hole saw blade cuts smooth…
Read more about this product
2 Review
The item is Vermont American 18381 Carbon Hole Saw Lock Installation Kit with Template for 7/8-Inch Latches. Used for Power Tool Accessories, Hole Saws. The product is manufactured in China. For cutting woods, plastics and composite materials up to 3/4-Inch thick. Teeth are precision sharpened to produce smooth cuts. Constructed of hardened and tempered…
Read more about this product