Anti-Vibration Shock Absorbing Rubber Mounting Bracket For Ductless Mini Split Air Conditioner Condensers Review

I bolted these with concrete screws to a large concrete paver as a foundation for a mini-split. Set on level gravel, I have not needed to stake the paver to the ground. I needed longer bolts than those provided to attach the outside unit itself. Other than that, these seem to be doing the job.

So far so good. My entire wall was rattling and vibrating before adding these little gems. It has reduced at least 98% of the noise/vibration I was experiencing.

, reduces the trapped debris under the units. We used tap screws and a small washer to bolt it down in a recent hurricane. None failed at the bolt or screw point

Works much better than the round ones that have a threaded rod thru them in isolating any vibration and noise--- That's my review.

They fit almost any outdoor ductless unit they look really good easy to install but if you’re looking for a vibration isolation I would pick something else. Good value.

It would have been nice if the top stud was longer . The top was not big enough to support the entire foot of the condenser . So I am questioning how long they will last. Could have added a bigger support for the foot, but the stud was to short to get the nut on.

These arrived today. It took only 15 minutes to install. Our outdoor condenser hangs on the wall on a metal bracket. In the winter we have a loud vibration on the wall while the unit is in heating mode. By installing these rubber feet it cut the vibration by 70%. You can still hear the unit running but now you really have to listen for it. I would recommend these to anyone who has a wall hanging outdoor unit!

not much to sya, got some AC splits for the house and needed these as they dont come with. Worked and fit perfect. That's my feedback.

Didn't have any issues with the install. We'll see a few years from now how well they keep holding that 3 ton mini split system.

I expected a really rigid rubber mount. These are surprisingly pliable and will minimize vibrations. My only complaint is that they should come with the associated mounting hardware, to mount to my existing brackets. On my way to the Home Dump to purchase the hardware needed. Ugh.

Mounted the outside unit on these vibration absorbers, then on a hollow plastic pad. Worried about noise at the bedroom window. They mount easily and security to both the unit and the plastic pad. While the unit is very quiet, there is almost no noise transmission to the hollow plastic pad that I worried would resonate. Very pleased with the combination of products.

Needed to quiet down my hot tub motor/pump. These worked so well I kept checking to make sure the dang motor/pump for the tub was still running!

I bought these isolators for a 24k BTU mini-split system. I compared several listings online, and this was the only one that appeared to include rubber bushings to go under the mounting nuts and clamp the AC feet in rubber without metal on metal contact. The feet were nice and heavy, the material was molded cleanly, the threaded studs were straight, etc. Great product for the price.

Jeacent Innovations, RM01A-1, Anti-Vibration Shock Absorbing Rubber Mounting Bracket for Ductless Mini Split Air Conditioner Condensers: Installed these on the Turbro ACS-740, Wall Mount Stand, Revain number B0921TDWFW, instead of the Turbro-supplied anti-vibe disks. Unlike the supplied disks, these Jeacent mounts truly decouple the compressor frame from the wall bracket. The wall bracket is installed on a wood-framed, insulated mini-barn and I cannot feel or hear when the compressor is…

Used this to mount the compressor unit of a Pioneer min-split AC to an outside wall. It works well and very little noise comes through. However, the drawing showed a 1-3/16" stud length. The actual length is 1". These feet come with a 1/4" rubber donut to put under the securing nut, but the stud was too short for that. The compressor frame uses up around 1/2". No way to put in a longer stud into the foot. Too bad, as 1-3/16" would have been long enough. It would be better for the manufacturer…

These are hollow! .and not really sturdy enough for a HVAC unit. Rubber cracked on one leg already. I'll be replacing with something more sturdy and capable.

These were a perfect fit for my Pioneer 18,000 BTU unit. They appear to be identical to the ones offered by the dealer, but at a much cheaper price.

Didn't really fit the giant A/C unit I installed but would recommend them to replace the default ones most split A/C systems ship with. These are very nice and will order again if I install more systems in the near future.

They fit and work, they are wide enough at the base to put in screws with a drill driver into the mat. They float the AC unit well.

Bought this to mount an split A/C unit on the side of my cabin. The mounts are holding very well even on an angle. Will definitely buy this brand again should I need more.