🔥 ASIAHORSE Graphic Card Cooler with LED Frame: 3 x 92mm Fans | Aura Sync Compatible Review

I will say my FE 3070ti is cooled significantly by this product. While playing I went from 85 cish to 65 cish temps. While 85cish aren't dangerous for this particular card, I'm concerned about durability, so I bought some extra fans hoping it would help keep them cool. This product actually works quite well for this purpose, but the downsides are really a pain. I'd also like to add that three more fans blowing on the GPU will likely keep it cool regardless of manufacturer. So don't praise them,

Absolutely helped keep my RTX 3090 temp down. This combined with some cheap tiny heatsinks kept the memory temperature below 75C - it used to be up to 89C. A pretty obvious influence, which is excellent. Noise wise I can't hear them compared to other fans in my case - I had to use software to see if they were even on! (They actually started working right away and didn't require any complicated setup!) The mounting system is a little wonky, as three dust covers have to be removed from the back…

Be careful, these are not PWM fans as advertised! not PWM. The first response I got was that I was wrong about the 3-pin ARGB connector and that the fan connector is 4-pin. After I sent them photos that the product I received has a 3 pin ARGB and a 3 pin fan, their answer changed to say the fans have a 3 pin connector and it doesn't there is a problem and their customers are satisfied. Are you kidding me?

Fan and RGB look great. The product has reduced my idle temps significantly considering my RTX 3070 fans are not spinning at idle. When idling it went from 52 to 29 degrees. In games, the temperature dropped from 64 °C to 60 °C. My only criticism is that the product just hangs as there is nothing to support it other than PCI screws and a bracket. At least with the GPU you have a PCIe connection to support it in the middle, with it just resting on a metal support that isn't enough for the weight

Quiet. Temperatures dropped 5°C on my EVGA GTX 1080 SC. Now at full load about 65-70°C. Not bad for a Pascal GPU. The attachment system is terrible. Get a GPU clamp and use it as there is no support at all on one side and it sags a bit in no time. In general, I'm satisfied, it looks good, but at 25 degrees, the temperature dropped 5 degrees, and easy installation? Thinking about a custom loop? This may be the value you need when trying to save money. Fans are cheap, treat them with care and…

installation behind the vertical GPU in an open case. Use it to blow hot air off the back of the 6800xt and move the air around the motherboard (hit the board and move up and feel a slight breeze off the RAM and VRM).1. Is working. A GPU with fans at 55% and 100% utilization for 24 hours sits on a 40c gou and, more importantly, a 60c.2 hotspot. Quiet: I tied its speed to the chipset and at 1000rpm I can't give it away.3. Looks good. Will report/edit review if I have any issues.

That's right, the metal mount for it isn't specifically designed for your computer. Some modifications required. However, it's one of the best slot coolers out there, which is why it's sold so often at Revain. In the end I just cut the bottom metal tab off with metal snips and secured it with two screws so I could slide it away from the GPU and give the 3090 some breathing room. Also, I just used my GPU stand to mount the fan as it needs to have some kind of stand against the mounting side of…

Installed fans directly under my card. Mind you I also have 3 case fans on the bottom for airflow. This card actually warmed up my GPU several degrees at 100%. I'm trying to reduce it to 0 and it really made the GPU cooler. Tried disabling the GPU fan, didn't help. I tried increasing the GPU fan and it was able to keep what I had without this card installed. RGB is good, but not worth the noticeable noise at 100% or the increase in GPU temp.