🔌 Bosch 11027 Oxygen Sensor: Versatile Fitment for Enhanced Performance Review

does not fit connectors on my 2003 BMW E46 325i Sedan M54 Made in April 2003. THESE O2 SENSORS FOR 325I MADE ON AND BEFORE DATE 3/2003. I think there is a year classification for the 325i in 2003. Others like mine were made after that date and use other O2 sensors and other miscellaneous engine parts I found out. For BMWs built after March 3rd you will need Bosch 15680 and 15681 downstreams (both will fit both downstreams). And for upstream you need Bosch 17215 and 17216 (both work for both…

If you're experiencing hard starting, poor acceleration, rough idle, black smoke out of the exhaust, or just have a dreaded P0193 code, there's more than a chance the fuel line pressure sensor is dying and would like to be replaced with a good new sensor. If the computer cannot determine the fuel pressure at the injectors, be prepared for a lean mixture in your combustion. In my condition, the Ford F-150 was running very rich with an incorrect reading of 11psi on the fuel rail. (hydrocarbon…

Bosch makes good parts so when I saw this unit I bought it without hesitation. When I received my part today, it was installed in just a few minutes. I spent a little more time unplugging the power connector from the old part so as not to damage it. You need to place a small flathead screwdriver on top of the latch and push it down, then gently pry it off the connector. I also stuffed it with paper towels before removing it from the engine and I only opened it slightly until the pressure was…

If you own a Mercedes S Class (2000-2006) this is a must. You should always have a spare part in the car because these things sometimes break without notice or with very little warning. This little Crankshaft Position Sensor (CPS) will leave you calm and dry in a deserted parking lot after watching a movie and having dinner on your first date. You proudly walk to your hundred thousand dollar car, turn the key and all you hear is, uh, uh, uh, uh, uh, noise. You know, the kind that makes you very

This gauge fixed my 2004 3.2L V6 Crossfire starting problem! I am 43 years old and this part was very easy to install myself. My problems started after I drove into town one day. When I tried to start the car to get home, it kept overturning but wouldn't start. I waited a few minutes and thankfully it started up again. When I got home I parked the car and tried to start it and again it kept turning but wouldn't start. The next morning when the engine was cold it started right away, but after…

Update: took 5 months - back to Denso). : two in front of the catalyst and this one after). First, Toyota is very sensitive to its sensors, which is why many people choose the Denso brand used by Toyota. That said, Denso sensors are at least twice the price, but they turn off the check engine light and last over 100,000 miles, which probably means a one-time replacement for most vehicles. Так что, если вы не пойдете по пути Denso, лучше всего подойдет Bosch, и, честно говоря, вероятно, проще…

The machine was bought without papers so I had no idea when they were replaced. My car hasn't given me any problems or codes, but as a preventative maintenance I decided to replace them. It was pretty easy, but it took a long time. The reason for this is that I used a crow's foot (22mm) instead of an O2 sensor socket. If you decide to buy an O2 sensor socket, make sure it is thick as the socket can bend if the O2 sensor is stuck very hard. The O2 sensor is located on the passenger side of the…

My 05 S430 didn't start the first time after a short stop. I ordered this part and installed it myself. 2 weeks and so far so good! The original part shows the BENZ and BOSCH part numbers, while this part shows only the BOSCH part number. Here are the rough removal steps after watching some good videos of yours. Pipe: 1. No need to remove the heat shield, just bend or push it down to give you more room to work with the E8 torx screw. I didn't do this when unscrewing the bolt, it was difficult…