Header banner
Revain logoHome Page
πŸ”ͺ inverter for stainless aluminum cutting with enhanced frequency logo

πŸ”ͺ Inverter for Stainless Aluminum Cutting with Enhanced Frequency Review

3

Β·

Average

Revainrating 3 out of 5Β Β 
RatingΒ 
3.0
πŸ”§ Industrial Power Tools, πŸ› οΈ Industrial Power & Hand Tools

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ”ͺ Inverter for Stainless Aluminum Cutting with Enhanced Frequency
img 2 attached to πŸ”ͺ Inverter for Stainless Aluminum Cutting with Enhanced Frequency
img 3 attached to πŸ”ͺ Inverter for Stainless Aluminum Cutting with Enhanced Frequency
img 4 attached to πŸ”ͺ Inverter for Stainless Aluminum Cutting with Enhanced Frequency

Description of πŸ”ͺ Inverter for Stainless Aluminum Cutting with Enhanced Frequency

[Cutting Ability] Automatic 110/220v ac-dc dual voltage,10-50A dc output, 1/2''(12mm) ideal clean cut and 3/5''(15mm) maximum severance cut on 220v;10-40A dc output, 1/3"(8mm) ideal clean cut and 2/5"(10mm) maximum severance cut on 110v. [Cutting Material] Compact plasma cutter has a handle for portability and uses non-hazardous compressed air to cut stainless steel, alloy steel, mild steel, copper,cast iron and chrome. [Post Time] Pre-made 3 seconds of blowing time after the torch released to cool down the torch head and consumables.Besides,the blowing time can be set by adjusting the knob. Breaker Recommendation:50A on 110V,30A on 220V. [Input Votage AC-DC] Dual voltage input automatic dual voltage / dual frequency (110/120 v 220/240 v 50/60hz).Air Pressure 60-70PSI suggested. [Warranty Assurance] We are a manufactory with over 10 years' experience of professionals producing the plasma cutter machines,3 year's warranty.Please add to cart and take it without hesitation.

Reviews

Global ratings 3
  • 5
    1
  • 4
    0
  • 3
    1
  • 2
    0
  • 1
    1

Type of review

Revainrating 1 out of 5

DO NOT SPEND YOUR MONEY. BAD CUSTOMER SERVICE. You take your money on the below average machine

I used this machine three times and the third time the fan stopped working and overheated. The flashlight didn't work and all I can smell is the smell of burnt rubber. I had about a quarter inch to cut the 2" flat bar into 1/8". It's been 2 days since the refund and they haven't honored it. waste of money.

Pros
  • Tools and Housewares
Cons
  • I will add later

Revainrating 3 out of 5

You get what you pay for.

I think you get what you pay for and I would like to spend a little more money. It works, but it doesn't cut the thickness as specified in the settings. It interrupts my 110 volts for 10 seconds each time, but my 220s have no problem with it. If you enjoy making small things then this is probably fine, but if you're looking for something for commercial use or heavy daily workloads you might be better off with an ESAB.

Pros
  • Plasma cutter
Cons
  • Without automatic

Revainrating 5 out of 5

Best investment I've ever made

I've wanted/needed a plasma torch for a long time. But I've always been content with a saw, a cut-off wheel, a band saw, etc. A few years ago brand name routers were about $800 for a 50-amp, but now they're $1,800. I got curious when I saw this car and the other good reviews made me even more curious. Until I clicked buy. I've had it for 3 weeks, for the money it's just great. I cut 18ga, 1/4”, 1/2” and even 3/4” with it. There is no cutting chart included, but once you get used to it you can…

Pros
  • Welder
Cons
  • Weak