Header banner
Revain logoHome Page
πŸ”§ hiletgo 3pcs pro mini atmega328p 3.3v 8m module board with crystal oscillator - arduino pro mini replacement, compatible with atmega128 logo

πŸ”§ HiLetgo 3pcs Pro Mini ATmega328P 3.3V 8M Module Board with Crystal Oscillator - Arduino Pro Mini Replacement, Compatible with ATmega128 Review

6

Β·

Poor

Revainrating 2 out of 5Β Β 
RatingΒ 
2.0
🧰 Computer Internal Components, πŸ’» Computer Components

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ”§ HiLetgo 3pcs Pro Mini ATmega328P 3.3V 8M Module Board with Crystal Oscillator - Arduino Pro Mini Replacement, Compatible with ATmega128
img 2 attached to πŸ”§ HiLetgo 3pcs Pro Mini ATmega328P 3.3V 8M Module Board with Crystal Oscillator - Arduino Pro Mini Replacement, Compatible with ATmega128
img 3 attached to πŸ”§ HiLetgo 3pcs Pro Mini ATmega328P 3.3V 8M Module Board with Crystal Oscillator - Arduino Pro Mini Replacement, Compatible with ATmega128
img 4 attached to πŸ”§ HiLetgo 3pcs Pro Mini ATmega328P 3.3V 8M Module Board with Crystal Oscillator - Arduino Pro Mini Replacement, Compatible with ATmega128

Description of πŸ”§ HiLetgo 3pcs Pro Mini ATmega328P 3.3V 8M Module Board with Crystal Oscillator - Arduino Pro Mini Replacement, Compatible with ATmega128

Pro Mini Atmega328 3.3V 8Mhz. It has been programmed for its bootloader, without the user to buy ISP burner for programming, user-friendly. This board connects directly to the FTDI Basic Breakout board and supports auto-reset. Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, accelerometers, sensors, etc).

Reviews

Global ratings 6
  • 5
    1
  • 4
    0
  • 3
    0
  • 2
    2
  • 1
    3

Type of review

Revainrating 5 out of 5

Does not come with bootloader - not Arduino ready!

These boards did not ship with a bootloader, which means they cannot be programmed to use the Arduino right out of the box. If you are a beginner or don't have the right tools to burn bootloader, this will be very difficult to use! I was able to burn the bootloader with my Atmel-Ice Basic but it was a frustrating process. I do not recommend buying from this seller. After writing the bootloader, the board works fine.

Pros
  • Always liked it
Cons
  • Negative is present

Revainrating 1 out of 5

A real workhorse - I/O port cards

Like - works reliably, allows for a lot of abuse and keeps ticking dislikes - not this particular vendor, but multi-vendor serial communication is incompatible . Some vendors have the ground pins on the right, others on the left.

Pros
  • Easy to read front panel
Cons
  • Not as thick as other options

Revainrating 1 out of 5

Bad bootloader failed to fix

I've bought a few of these lately due to the trade war and chip shortages. I'm using the Arduino IDE running on the Raspberry Pi. I'm not happy they have this problem. Fixing them was/is/will be a pain. I had to do that. First, the Arduino IDE uses a custom version of avrdude, so I downloaded a standalone version of avrdude to my Pi using apt-get. They will not disturb each other. Then in the Arduino IDE I made the detail settings and compiled (but not downloaded - important). The text output…

Pros
  • Great price
Cons
  • About

Revainrating 2 out of 5

Bad controls on these boards.

We should have read other reviews first. On such voltage regulators die, sometimes with smoke. As others have said the processor part is fine, it can be powered from the VCC pin (after removing the faulty regulator) with an external regulator or add a new regulator on the back (e.g. LD117V33).

Pros
  • I like everything so far
Cons
  • Repair

Revainrating 1 out of 5

Bad products for computers and accessories

Stay away from these clones. All three burned down within minutes. They programmed chaotically before they exploded, programmed once, then they weren't recognized, and then suddenly they programmed again. Go with Elegoo for good clones.

Pros
  • Finally bought
Cons
  • Upgradable

Revainrating 2 out of 5

All three don't sync to FTDI

After soldering the connectors, none of the three sync to my FTDI with the jumper set to 3.3V. I've tried overriding the bootloader with a spare UNO, and it was successful . But even after flashing the bootloader, they didn't sync. I cannot recommend this product as they were all DOA. I have two other WayinTop Pro minis that sync perfectly with my FTDI.

Pros
  • GOLS certified
Cons
  • too dumb