Intelligent charger LiitoKala Lii-PL4 Review

LiitoKala Engineer Lii-PL4 LitoKala Lii-PL4 Intelligent charger LiitoKala Lii-PL4 for Ni-MH, Li-ion and LiFePO4 batteries with automatic adjustment of the charge current: 500, 1000, 2000mA and selection of the final charge voltage of the lithium-ion battery 3.6V - 4.2V - 4.35V. Compatible with the following battery types: Li-ion / LiFePO4: 21700, 20700, 26650, 22650, 18650, 17670, 18490, 17500, 17335, 16340 (RCR123), 14500, 10440 Ni-MH / Ni-Cd: AA, A AA, C LiitoKala Lii-PL4 is a versatile smart charger compatible with almost all cylindrical batteries, thus eliminating the need for multiple chargers. LiitoKala Lii-PL4 automatically recognizes lithium-ion, nickel-metal hydride and nickel-cadmium batteries, charges lithium-phosphate (LiFePO4) batteries, as well as Li-ION batteries with a final voltage of 4.35V. Peculiarities: Charging batteries of various types and chemistry Compatible with the following types of batteries: Li-ion/LiFePO4: 21700,20700,26650,22650,18650,17670,18490, 17500,17335, 16340, (RCR123), 14500, 10440 Ni-MH / Ni-Cd: AA, AAA, C Support for modern Li-ION batteries with a final voltage of 4.35V Smart circuit automatically detects battery type and charge mode (CC, CV, DV/DT) Output current: Li-ion / LiFePO4: 500 - 4acb, 500 - 3acb, 1000 - 2acb, 2000 - 1acb. Ni-MH / Ni-Cd: 500 - 4acb, 500 - 3acb, 1000 - 2acb, 1000 - 1acb. Overcharge protection - automatic termination of charge for Li-ion / LiFePO4 batteries after full charge Ability to activate deeply discharged Li-ion batteries Battery Reversal Protection Mains power 220V (cable included) Powered by car adapter 12V RoHS and CE certification Quick guide: Install the batteries with the correct polarity (the device has protection against incorrect installation of batteries). Within 5 sec. the device will detect the battery type (Ni-MH or Li-ion) and start charging. The progress of the battery charge is displayed in the form of 4 flashing indicators. Each indicator indicates approximately 25% battery charge. When the battery is fully charged, all indicators light up without flashing. When installing Li-ion 4.35v and LiFePO4 batteries, you must select the final charge voltage. (The default always turns on the charge up to 4.2V). To do this, within 5 seconds after installing the battery, press the MODE control button. Use the indicator to select the desired final charge voltage. The inscriptions on the indicators correspond to: The charging current depends on the number and type of installed batteries: For Ni-MH / Ni-Cd batteries: 500mA - 4acb, 500mA - 3acb, 1000mA - 2acb, 1000mA - 1acb. For Li-ion / LiFePO4 batteries: 500mA - 4acb, 500mA - 3acb, 1000mA - 2acb, 2000mA* *attention! The 2000mA charge current is enabled for only one Li-ION battery in the far right compartment. The device has a function to activate deeply discharged batteries. But keep in mind that charging may not detect batteries with voltage: - Ni-MH: less than 0.2V - Li-ION: from 1.6V to 2.2V Specifications: Input: AC 110-240V 50/60Hz / DC 12V 1A Output current: Li-ion / LiFePO4: 500 - 4acb, 500 - 3acb, 1000 - 2acb, 2000 - 1acb. Ni-MH / Ni-Cd: 500 - 4acb, 500 - 3acb, 1000 - 2acb, 1000 - 1acb. End charge voltage: 3.65V / 4.2V / 4.35V / 1.48V Dimensions: 133mm × 100mm × 35mm Weight: 175g Complete set: Charger Mains cable Warranty card Instruction in Russian.