Header banner
Revain logoHome Page
πŸ–€ laser marking powder - 'brilliance laser inks' - bli101mbpwd250 black laser ink powder for metal marking with co2/fiber/yag (250g) logo

πŸ–€ Laser Marking Powder - 'Brilliance Laser Inks' - BLI101MBPWD250 Black Laser Ink Powder for Metal Marking with CO2/Fiber/YAG (250g) Review

4

Β·

Very good

Revainrating 4.5 out of 5Β Β 
RatingΒ 
4.5
πŸ“ Paper & Paper Crafts, 🧢 Crafting

View on AmazonView on Π―M

Media

(1)
img 1 attached to πŸ–€ Laser Marking Powder - 'Brilliance Laser Inks' - BLI101MBPWD250 Black Laser Ink Powder for Metal Marking with CO2/Fiber/YAG (250g)

Description of πŸ–€ Laser Marking Powder - 'Brilliance Laser Inks' - BLI101MBPWD250 Black Laser Ink Powder for Metal Marking with CO2/Fiber/YAG (250g)

βœ… 100% SATISFACTION GUARANTEE OR MONEY BACK:Settings and marking techniques may vary depending on the laser and metal product being marked. We can usually resolve most marking issues with simple setting adjustments. Please feel free to contact us directly. βœ… FOAM BRUSH INCLUDED: Add denatured alcohol or similar RATIO 1:1. Mix/Shake well, Use foam brush to apply on the substrate surface, apply a thin coat using left to right motion, as long as you do not see through the surface.Use the suggested laser settings in our FAQ section as a starting guide line or feel free call our Technical Support Team. βœ… AIR BRUSH or SPRAY-GUN APPLICATION: Add denatured alcohol or similar. RATIO 1:2 or 1:3. Mix/Shake well before spray. βœ… GENERAL GUIDELINES βœ… SETTINGS: Scan QR CODE on product label to see our suggested laser settings in our FAQ section of our website. CO2 LASER - 25 Watt Minimum Required (100% P / 15-30% S / 500-700 DPI). FIBER LASER - 10 Watt Minimum Required (@ 10 Watt PWR / 50 mm/sec / 80-500 Q-Freq. / DPI- 0.1mm Hatch) Low watt Diode Lasers are not recommended. βœ… DRIES QUICKLY βœ… NO WAIT REQUIREMENT: To further speed up the process use hair dryer or heat gun to dry within seconds.

Reviews

Global ratings 4
  • 5
    2
  • 4
    2
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

I've tried them all, this one works the best!

This laser ink saves lives when laser marking brass. The last product I used was cerMark and my 60 watt CO2 laser left no permanent marks on the brass. Now I don't have to use even close to full power to get a dark spot that won't go away.

Pros
  • Accessories
Cons
  • New competitors

Revainrating 4 out of 5

Ideal for carbon dioxide cars

The powder product is a bit more difficult to use than the aerosol version but the results are great. Instead of using the included foam brush to apply, I used an eyedropper and blended it thinly so it spread evenly over the product. Be sure to mix denatured alcohol, not isopropyl. The bottom line is that you get a lot more bang for your buck in powder form, so if you don't mind the extra hassle, this is the best value for your money. I've also found that disabling air support gives the best…

Pros
  • Paper and Craft Paper
Cons
  • Crumpled

Revainrating 5 out of 5

I've tried them all, this one works the best!

This laser ink is a lifesaver when laser marking brass. The last product I used was cerMark and my 60 watt CO2 laser left no permanent marks on the brass. Now I don't have to use even close to full power to get a dark spot that won't go away.

Pros
  • βœ… BY SPRAYING or SPRAY APPLICATION: Add denatured alcohol or similar material. RATIO 1:2 or 1:3. Mix/shake well before spraying.
Cons
  • High Price

Revainrating 4 out of 5

Great option for CO2 machines

The powder product is a bit more difficult to use than the aerosol product, but the results are great. Instead of using the included foam brush to apply, I used an eyedropper and blended it thinly so it spread evenly over the product. Be sure to mix denatured alcohol, not isopropyl. The bottom line is that you get a lot more bang for your buck in powder form, so if you don't mind the extra hassle, this is the best value for your money. I've also found that disabling air support gives the best…

Pros
  • βœ… PORONA BRUSH INCLUDED: Add denatured alcohol or similar solution in a 1:1 ratio. Mix well/shake well, apply to substrate surface with a foam brush, apply a thin coat from left to right until surface can be seen through. Use the recommended laser settings in our FAQ section as a starting point. or call our technical support.
Cons
  • disappears