Moon Photo Frame Epoxy Resin Molds For DIY Home Decor - Unique Moon Shape Silicone Molds For Picture Frames And Table Accessories Review

Not a bad mold still need to work out how much resin is needed to fill it without wasting any. Think I over filled them a bit, the outer ring was a bit tight and wouldn't spin so may need sanded the others were just fine so there should be a way for the outer ring to be fine with out sanding as well.The pegs that are built in for alignment didn't come out either not sure if I didn't get resin in there or they stayed when i de-molded it but keep that in mind also. Over all pretty happy with it.

This is a very cool mold. I like the Moon Perpetual Calendar Resin Mold by ISSEVE because I really love celestial themed decor. This is a very unique mold and I've not seen one like it before. This is a good mold to use with regular casting resin as it's open back and not very thick. Each of the mold pieces cure separately, and then are placed together to use as a calendar. This will look great with mica powder and glitter. Thanks for reading my review. I hope my information is helpful to you…

It should come with directions. Me n 2 neighbors drank a 6 pack sitting around the table, trying to put the calendar together. However, it's a super easy to use mold and came really fast.HERE'S HELP:Fill both moon shaped molds as usual, but, the one with the circles in it - only fill the circles, not the whole mold. Then, sand the edges of the circle inside n out after removing so they'll slide easy to change the date. Then, paint a small area where the numbers and symbols are imprinted into…

I had to redo some. The rings need to be full but not overfill. The moon thick base cures faster. The front moon piece bent after I removed it and it seemed good. I had the big part get bent a bit. I needed a flat surface. They didn't fit. I used fresh resin instead of glue. Along edges. I actually was able to use the heat gun to soften enough to adjust all parts. Finally it fit. Butvall of the days and numbers and all need to be filled in. One try I used marker on the words but not all of them

I was so looking forward to this, and other moldsI got at the same time.This one, 2 of 3 lives, I was able to demold, but the 3rd, the resin is stuck to the mold in many places.I have tried heart, cold, and so far nothing works.I am afraid this is a loss, of resin, which is expensive, and mica powers for dying the resin, and especially the mold. :-(.Very 😞 disappointed.Another mold, a jewelry mold, some items (half) stuck in the mold, and there's no undoing those.Use at your own risk.

This is really kewl concept for a mold that I hadn't personally run across so far in my exploring doing resin work. So right off the bat understand this isn't a standard mold. This takes a little work to put together but its not hard and is worth it. The mold isn't super deep but I think it's where it needs to be in that regards otherwise the rings might be too heavy to move. I found it easier to use glue across the non-moving part to hold things in place but I'm curious if there is…

This is a study and durable mold. The design is a great gift idea. I can make personal perpetual calendars for gifting. Great product.

The holes and pegs for the two main pieces don't line up at all and one piece was significantly bigger. Waste of money.Would not recommend.unless it was to someone i didn't like.

This arrived today, molds were folded in half and crammed in a tapped plastic bag. Is this new, used or a return? Came with no instructions. I am sure I can figure it out but it would nice to know how high to fill everything.

Its a nice enough set of molds. But take extra care in pouring.you'll end up with a lot of sanding to get the discs moving smoothly once assembled.

IT IS a good mold after all, BUT it does not want to stay together, once you snap all together, so suggest using glue, plus in my opinion it should be made where product coming out of mold should be thicker, aka the pour cavity should be a little deeper

There is an uneven place in the top piece mold. The pieces fit together bottom to bottom, so an uneven bottom to the top piece means they won't fit together. Wasted lots of resin 😡

Not enough depth to the letters or numbers … in other words mold isn’t deep enough to achieve the proper effect The mold might not be suitable for beginners and might require prior experience with such crafts.

Fun project. Enjoyed making a few of these. Make sure you cure it or let it sit for a week. The outer ring Bends easy. That's my review.