Header banner
Revain logoHome Page
🎧 enhance your audio experience with the ne5532 stereo preamplifier diy kit: full control over volume, treble, midrange, and bass tones logo

🎧 Enhance Your Audio Experience with the NE5532 Stereo Preamplifier DIY Kit: Full Control Over Volume, Treble, Midrange, and Bass Tones Review

5

Β·

Very good

Revainrating 4.5 out of 5Β Β 
RatingΒ 
4.6
🍿 Home Theater, 🎡 Home Audio

View on AmazonView on Π―M

Media

(4)
img 1 attached to 🎧 Enhance Your Audio Experience with the NE5532 Stereo Preamplifier DIY Kit: Full Control Over Volume, Treble, Midrange, and Bass Tones
img 2 attached to 🎧 Enhance Your Audio Experience with the NE5532 Stereo Preamplifier DIY Kit: Full Control Over Volume, Treble, Midrange, and Bass Tones
img 3 attached to 🎧 Enhance Your Audio Experience with the NE5532 Stereo Preamplifier DIY Kit: Full Control Over Volume, Treble, Midrange, and Bass Tones
img 4 attached to 🎧 Enhance Your Audio Experience with the NE5532 Stereo Preamplifier DIY Kit: Full Control Over Volume, Treble, Midrange, and Bass Tones

Description of 🎧 Enhance Your Audio Experience with the NE5532 Stereo Preamplifier DIY Kit: Full Control Over Volume, Treble, Midrange, and Bass Tones

Power supply circuit adopts full bridge rectifier, the four pins of rectifier is respectively in parallel connected with decoupling capacitor, effectively eliminate the high frequency interference of AC power grid. The chip has high conversion rate and strong drive ability, which will greatly help your project. Small clutter interference of power grid, stable and reliable performance. Wide frequency band and small noise, easy to use. Pay attention that it can not use 12V battery or DC directly as power supply.

Reviews

Global ratings 5
  • 5
    3
  • 4
    2
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 4 out of 5

Great value for money

Easy assembly. Worked the first time I turned it on. Sounds very good for the price. Used other pots so I could fit in the box. The rest I used accessories.

Pros
  • Easy to set up
Cons
  • There are more interesting options.

Revainrating 5 out of 5

Easy to build good amp

I built this as part of my 200w amp system at home. I haven't installed it yet as the build is on hold for extra parts. Once I have it installed I will write another review on its performance.

Pros
  • Nice packaging
Cons
  • Can't remember

Revainrating 5 out of 5

Works great if you know how to solder

Works perfectly. If you're good at soldering and don't mind a permanent installation, here's your $200 headphone amp with budget EQs. It took about 30 minutes to make. I was powered by a 120/12v AC transformer out of the wall.

Pros
  • Finally bought it
Cons
  • Some cons

Revainrating 5 out of 5

Nice Clean Preamp: Home Audio

This was a fun easy kit, no diagrams or guesswork. It sounded so good I bought another one for my other system. The sweat was the body I put it in. I installed my first rack on a 1/8th rack aluminum panel. The board had to be thinned to leave enough room for the threads on the potentiometers to fit nuts and washers. The maximum thickness is about 0.065 inch. The pan shafts fit into 9/32" diameter holes and are spaced approximately 0.932" apart. A little less than an inch. Enjoy!

Pros
  • Special Offer
Cons
  • Hard to Tell

Revainrating 4 out of 5

I highly recommend this little op amp with tone/voltage preamp! It's fun to build and sounds great!

I create professional quality products with a modular approach. I chose this preamp because it was a do-it-yourself kit and it uses a very popular and very stable operational amplifier (operational amplifier) that has good gain, very good signal-to-noise ratio, acceptable harmonics distortion, a good input impedance and with 400-600mV input signal, it can easily handle any amplifier board of your choice. Other subtleties are numerous; If you look closely at the PCB, the power supply ground and…

Pros
  • Wide range
Cons
  • So so