🔌 Mining Molex Thsion Riser Adapter Review

GPUs show up in the system, but immediately freeze during peak loads, causing system instability. I tried 3 different AMD and NVidia cards with the same result. This should work for data traders, but not for mining. I tested it on Windows and HibeOs with the same result. Also, the plastic wasn't cut perfectly, making it difficult to fit the m2 socket. Don't waste your time here, I bought 2 and they both suck.

I was hoping they would be different but I'm starting to think there is only one material company in China and they keep making new ones Revain customers. The boards work great. AFTER I took them a dremel/grinding wheel and removed the skin on the pin end of the card. If you need to do the same, remember that the circuit board is just a material that can be sanded down. Just don't remove too much to avoid damaging the pins. present, but does not ensure proper pin contact). There was even…

Thing works great. I added another GPU with an unused m.2 slot. As previously mentioned, you will need to remove a small piece of the circuit board. The price of this item doesn't bother me.

Decent product but plug needs a plastic finish. As mentioned in other reviews, I had to carefully drill out the plug to install it properly. When using for mining (for the 7th, 8th card on the motherboard) note that you may need a processor with internal graphics for this to work with some motherboards (Z390, etc.). Works without problems so far. There was also a screw. 4 stars if you are good with your Dremel. 0 stars if you don't have a Dremel.

I use them in combination with Mintcell GPU add-ons and the USB port of the add-ons connects directly to the USB port of the adapter. I can now run 8 GPUs on my rigs. The only caveat is the PCB material isn't cut quite right so you'll have to trim the sides and slot a bit, but once that's done they fit and look great.

great for mining there are 2 and both for rtx 3070 if you need it for mining go ahead and buy it. I've been using it for a few months and it works perfectly (not very good laser cut or IDK but you just need to clean it a little and it fits perfectly in the m.2 slot). You just need to remove excess circuit boards and good mining

Works great and is plug and play! Allowed me to add another PCIe slot to my motherboard for my 5700xt. As other reviewers have stated, it has an extra sheet of plastic due to sloppy cutting at the factory. But with a small knife, file or sandpaper you can easily fix it. Just be careful not to damage the gold pins. Also doesn't come with a screw so make sure you have a mobo screw.

GPUs appear in the system, but freezes immediately during peak loads, resulting in unstable system operation. I tried 3 different AMD and NVidia cards with the same result. This should work for data traders, but not for mining. I tested it on Windows and HibeOs with the same result. Also, the plastic wasn't cut perfectly, making it difficult to fit the m2 socket. Don't waste your time here, I bought 2 and they both suck.

Decent product but connector needs plastic shroud. As mentioned in other reviews, I had to carefully drill out the plug to install it properly. When using for mining (for the 7th, 8th card on the motherboard) note that you may need a processor with internal graphics for this to work with some motherboards (Z390, etc.). Works without problems so far. There was also a screw. 4 stars if you are good with your Dremel. 0 stars if you don't have a Dremel.

I was hoping they would be different but I I'm starting to think there's only one company making things in China and they keep creating new Revain accounts. Boards work great. AFTER I took them a dremel/sanding wheel and removed the highlight at the pin end of the card. If you need to do the same, remember that the circuit board is just a material that can be sanded. Just don't remove too much to avoid damaging the pins. present, but does not ensure proper pin contact). There was even material…