Header banner
Revain logoHome Page
timber wolf bandsaw blade 93 1 cutting tools and band saw blades logo

Timber Wolf Bandsaw Blade 93 1 Cutting Tools and Band Saw Blades Review

4

·

Very good

Revainrating 4.5 out of 5  
Rating 
4.5
🔧 Band Saw Blades, 🔪 Cutting Tools

View on AmazonView on ЯM

Media

(1)
img 1 attached to Timber Wolf Bandsaw Blade 93 1 Cutting Tools and Band Saw Blades

Description of Timber Wolf Bandsaw Blade 93 1 Cutting Tools and Band Saw Blades

Milled teeth are 50 PERCENT SHARPER than competitors stamped or crush ground blades. Precision Induction hardening throughout the blade vs competitors flame hardening. Tooth edge is 20 PERCENT harder than any high carbon steel resulting in extended sharp time. More ductile steel than any high carbon steel leads to extended flex life and a cooler running blade. Thin kerf.

Reviews

Global ratings 4
  • 5
    2
  • 4
    2
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

GOOD BLADE! best blade ever

I have been using a 14 inch jet saw for about 20 years and this is the first Timber wolf blade I have ever had Bought. I've fought cheap blades and the Olsen blade with mixed results. But this is from Timber Wolf - best I've ever used, sharp, hungry and soft cutting! I will not go back to smaller blades. Expensive, yes, but I spend a lot more time productively than with the saw.

Pros
  • Tooth edge is 20 PERCENT harder than any carbon steel for longer sharpening time
Cons
  • Slightly wrinkled

Задняя часть лезвия не была полностью выровнена при сварке, поэтому лезвие перемещается вперед-назад при сварке (у меня есть видео about that). Sawing the back of the blade would have made it worse so I carefully adjusted the rear blade thrust bearings and everything works fine. I don't have to send it back. but i was a bit disappointed. I really liked the information on how to set the blade tension correctly. Not only did it work, but it turned out that my Craftsman band saw was properly…

Pros
  • Более пластичная сталь, чем любая высокоуглеродистая сталь, обеспечивает более длительный срок службы при изгибе и более низкую температуру вращения лезвия
Cons
  • Устаревшая модель

Задняя часть лезвия не была полностью выровнена при сварке, поэтому лезвие перемещается вперед-назад при сварке (у меня есть видео about that). Sawing the back of the blade would have made it worse so I carefully adjusted the rear blade thrust bearings and everything works fine. I don't have to send it back. but i was a bit disappointed. I really liked the information on how to set the blade tension correctly. Not only did it work, but it turned out that my Craftsman band saw was properly…

Pros
  • Более пластичная сталь, чем любая высокоуглеродистая сталь, обеспечивает более длительный срок службы при изгибе и более низкую температуру вращения лезвия
Cons
  • Устаревшая модель

Revainrating 5 out of 5

Great band saw blades

My band saw is over 40 years old and has seen metal and wood abuse, hobby and industry in its long career so I decided to give these blades away as gifts. I've installed them exactly as I've installed Starrett blades many times and the results have been fine - nothing special. I then read the instructions and reinstalled the blades according to the manufacturer's instructions. Noticed a much improved cut finish (wood - not metal) with reduced feed pressure and no tendency for the blade to…

Pros
  • Fine kerf
Cons
  • Not as thick as other saws