🖥️. Single Board Computers
3 Review
Easy to use. Less I/O ports are occupied, only four - VCC, GND, SDA (serial data line), SCL (serial clock line). Support IIC protocol. The I2C LCD1602 library is provided, so you can call it directly. With a potentiometer used to adjust backlight and contrast. Power supply: +5V.
3 Review
The MF522-AN module design the circuit of card read by using the original Philips MFRC522 chip. Easy to use, low cost, and applicable to equipment development and card reader development etc. Applicable for the user who need to design or manufacture the RF card terminal. The module can be directly loaded into the various reader molds. The module use a…
Read more about this product
3 Review
1024x600 hardware resolution. Resistive touch control. Compatible and Direct-connect with any revision of Raspberry Pi (except the Pi 1 model B or Pi Zero, which requires an HDMI cable). Drivers provided (works with your own Raspbian/Ubuntu/Kali/Retropie). Also works as a computer monitor, in this case, touch panel is unavailable and HDMI cable is…
Read more about this product
3 Review
This is an upgraded version of a set-top box kit. In addition to leading the miniHDMI of the Raspberry Pi to the back of the panel, it also provides a full-size HDMI interface. The expansion board will provide a USB interface and a 5V power supply terminal on the front panel to connect other 5V peripherals. The 4010 blue light fan can dissipate heat…
Read more about this product
3 Review
For the document and download information, refer to Geekworm WiKi searcch (3.5_LCD_B). Note: 1. The Raspberry Pi 4B mother board and cooling fan is not included in all the packing list. 2. The black ABS case only suitable for this 3.5 inch screen with Raspberry Pi 4 Model B, do not support other Raspberry Pi versions. Not support install cooling fan…
Read more about this product
3 Review
IMX219-120 Camera,8 Megapixels.Sensor: Sony IMX219.Resolution: 3280 × 2464.120° FOV. Lens specifications: CMOS size: 1/4inch. Aperture (F): 2.2. Focal Length: 1.88mm. Angle of View (diagonal): 120 degree. Distortion: <13.6%. Lens dimensions: 6.5mm × 6.5mm. 4 screw holes Used for attachment. Provides 3.3V power output. Dimension: 25mm × 24mm. Combined…
Read more about this product
3 Review
IMX219-170 Camera.Sensor: Sony IMX219.8 Megapixels.Resolution: 3280 × 2464.170° FOV. Lens specifications: CMOS size: 1/4inch. Aperture (F): 2.0. Focal Length: 2.2mm. Angle of View (diagonal): 170 degree. Distortion: <22%. 4 screw holes Used for attachment. Provides 3.3V power output. Dimension: 32mm × 32mm. Combined with the Jetson Nano AI computer…
Read more about this product
3 Review
5-9VDC power (can run at 3.5V but color will be dimmed), constant current 18.5mA per LED (~55mA max total per pixel), Chainable design. What's a wearable project without LEDs? Our favorite part of the Flora platform is these tiny smart pixels. Designed specifically for wearables, these updated Flora NeoPixels have ultra-cool technology: these…
Read more about this product
3 Review
Compatible with Raspberry Pi Zero/1/2/3 B/B+/4B;2Pack,please refer to ASIN:B08C2DJBT2;5Pack,please refer to ASIN:B08C2F2Z2P. GPIO Edge Extension is a module that leads the 40Pin GPIO pins of the Raspberry Pi out of convenient use. Vertical Pin header. Horizontal Pin header. Package Includes:1 x GPIO Edge Extension
3 Review
Specially made to connect a camera to a Raspberry Pi Zero or Zero W. Total length is 16 cm (6.3 inch). Works with all Raspberry Pi compatible cameras that accept the standard 15 pin 1.0 mm pitch cable. Has black stiffeners at each end to make installation easier.
3 Review
For Arduino-compatible Board. USB connection off board. Supports auto-reset;DC input 3.3V up to 12V. Pro mini have a lower max current draw compared with UNOs and Megas, so pls don't run too many things off of VCC. What you will get is: 2 X Pro mini 3.3V 8MHZ
3 Review
Product CharacteristicsThe DAOKI Development Temperature Humidity Breadboard, a part of the Single Board Computers category, is an all-inclusive ESP8266 Weather Station IoT Starter Kit. This comprehensive kit features an ESP8266 ESP-12E Development Board, a high-quality 0.96" OLED display, and a reliable DHT11 Temperature and Humidity Sensor. With a USB…
Read more about this product
3 Review
The ETH/USB HUB HAT (B) is an Ethernet and USB HUB designed for Raspberry Pi, providing 1x RJ45 Ethernet port and 3x USB 2.0 ports. 3x extended USB ports, compatible with USB 2.0 / 1.1. Incorporates RTL8152B Ethernet chip, supports 1x RJ45 Ethernet port, 10/100M auto-negotiation. Pogo pin design, for direct connecting with Raspberry Pi Zero/Zero W/Zero…
Read more about this product
3 Review
The USB HUB HAT (B) is a 4x ports USB HUB designed for Raspberry Pi. It's pogo pin design is specialized for Zero series, while the onboard normal USB connector can be used to connect with other Raspberry Pi boards or PC through a USB cable. 4x extended USB ports, compatible with USB 2.0 / 1.1. Pogo pin design, for direct connecting with Raspberry Pi…
Read more about this product
3 Review
The case can be used as raspberry pi case with mini cooling fan and 3.5 inch screen installed. Please note that the ABS case is specially designed for Raspberry Pi 4 Model B only. The 3.5 inch LCD touch screen has 480 x 320 resolution, with resistive touch control; SPI Interface; Power: 5V 0.13A. The LCD touch screen can use GPIO interface for power…
Read more about this product
3 Review
Raspberry Pi 4B/3B+ GPIO Shield Expansion Board. GPIO Expansion Board. Raspberry Pi Shield. Raspberry PI 4B/3B+ With Screws. Multifunction GPIO Extension Board 1 to 3 Port DIY
3 Review
Raspberry Pi Low-Profile CPU Cooler Kit for Raspberry Pi 4. Metal Case Features:It not only provides good protection to your Raspberry Pi and also offering excelent heat dissipation. Fan Features: Color LED fan with automatic color change;Single-stack tower-style heatsink;DC 5V Power in (Can be powered by the Raspberry Pi). 5mm copper tube;Super heat…
Read more about this product
3 Review
This LoRa board comes unassembled, soldering is required, not equipped with lithium battery. You will receive, 1pcs board new version V2 with better quality, 1pcs antenna, and 1pcs jst battery connector 1.25mm male. When you use this oled board, you need to use 2pcs together. One is used for receiving and another for sending. Espressif esp32 chip +…
Read more about this product
3 Review
Package inlcuded:2pcs Red DC 5V 2 Channel Relay Module +2pcs Black 5V 2 Channel Relay board 5V 2-Channel Relay interface board, Meet your different need. Equiped with high-current relay, AC250V 10A ; DC30V 10A. Voltage:5V, 2 Channel. These modules can be set high or low triggered by jumper. Standard interface that can be controlled directly by…
Read more about this product