🖥️. Single Board Computers
3 Review
Supports I2C (default), configurable slave address, supports SPI, switch to SPI via I/O setting. Onboard voltage level translator, compatible with 3.3V/5V operating voltage. Humidity sensing: 0~100%RH (resolution 0.008%RH, accuracy ±3%RH, response time 1s, delay ≤2%RH). Temperature sensing: -40~85°C (resolution 0.01°C, accuracy ±1°C),barometric pressure…
Read more about this product
3 Review
Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards. 128×32 Pixels 2.23inch OLED Display Module,Embedded SSD1305 Driver, Using SPI/I2C Bus. Adopts both 4-wire SPI and I2C interface, better compatibility, fast data rate. Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples)
3 Review
High speed TensorFlow Lite inferencing. Low power. Small footprint. NXP i.MX 8M SOC (Quad-core Cortex-A53, plus Cortex-M4F). Google Edge TPU ML Accelerator Coprocessor
3 Review
0.96" SSD1306 128X64 OLED LCD Display with I2C IIC SPI Serial. Drive Duty: 1/64 Duty. Font Color: White. Panel Size: 26.70mm x 19.26mm x 1.85mm. High resolution: 128 * 64
3 Review
★Double BTS7960 large current (43 A) H bridge driver . 5V isolate with MCU, and effectively protect MCU; 5V power indicator on board;. ★Voltage indication of motor driver output end; can solder heat sink. ★Double BTS7960 H-bridge driver circuit, with a strong drive and braking, effectively isolating the microcontroller and motor driver! High-current 43A…
Read more about this product
3 Review
ATMega 32U4 running at 5V/16MHz;Supported under Arduino IDE v1.0.1. On-Board micro-USB connector for programming. 4 x 10-bit ADC pins;12 x Digital I/Os. The acceptable voltage range is 6 to 9 V. NOTE:Before running the procedure, pls install the Arduino IDE software. When you open the Arduino IDE software, pls go to the tool and choose the board…
Read more about this product
3 Review
This is GY NEO 6MV2 GPS Module NEO-6M GY-NEO6MV2 Board with Antenna for Arduino New,The default baud rate: 9600. Non-brand New Chip, but the use of the same effect.,Module with antenna, mini size with strong signal. EPROM save the configuration parameter data when power down,With data backup,With LED signal lights,Compatible with various flight control…
Read more about this product
3 Review
CPU Frequency : 4*Cortex-A7 Up to 1.2GHz. Memory RAM :1GB(16-bit). Storage : NC/8GB & MicroSD*1 for external storage up to 128GB. Connectivity : Dual Network Port and Fast Ethernetports, onboard WiFi & Bluetooth module. MicroUSB*1: MicroUSB 2.0, OTG & Power In AND USB Host: 2.0 Type A x2
3 Review
【You will get】Raspberry pi 4 model B case, 5.1V 3A USB-C power supply with ON/Off switch, 1 PCS cooling fan, 4PCS aluminum radiator, 4PCS rubber, 1 put screwdriver. 【Very good material】Beautiful aluminum alloy middle frame, not easy to damage, more durable, designed specifically for raspberry pi 4, will not affect the reception of WIFi or bluetooth…
Read more about this product
3 Review
plugs right into a Pi's 40-pin GPIO connector. powers the Pi through a low-Rds MOSFET for minimal voltage drop. Can power even the 3B+. Has two 2-pin JST connectors for measuring any voltage in your project up to 16V. Lots of connectors including USB for input power, a 2x2 header for input and output power, two 2-pin JST connects for measuring voltages…
Read more about this product
3 Review
Package included:2pcs ESP32-CAM-MB Camera Module and 2pcs USB-TTL Serial Adapter Module. HK-ESP32-CAM-MB adopts Micro USB interface, convenient and reliable connection method, convenient to apply to various IoT hardware terminal occasions. HK-ESP32-CAM-MB module can work independently as the smallest system. A new WiFi+Bluetooth dual-mode development…
Read more about this product
3 Review
Raspberry Pi 4 Model B Computer 4GB RAM, Official Case, Official Fan and heatsink, Official Power Supply, Official HDMI cable, Official MicroSD 32GB with Raspberry Pi SO preinstalled, ON/OFF switch.
3 Review
Features: we provide you 8 length flex extension cables, compatible with raspberry pi camera, they are 10 cm, 15 cm, 20 cm, 25 cm, 30 cm, 40 cm, 50 cm, 100 cm, and both ends are 15 pin 1.0 mm pitch interface; And 1 length cable, compatible with raspberry pi zero camera, which is 16 cm, the end is 15 pin 1.0 mm pitch interface. Easy to connect: our…
Read more about this product
3 Review
Xilinx XC7A100T-L2FGG484E FPGA. 256MB DDR3-800. 128Mb configuration flash. PCIe x4 gen 2. M.2 2280 Key M (same as SSD NVMe)
3 Review
400+ Building Blocks: You can build all kinds of interesting shapes you want, not limited to our official 20 kinds of building, better stimulate the kid's imagination and improve their hands-on ability. Packed with 3 Electronic Sensors: the Line-following sensor, the Ultrasonic sensor and the Water level sensor, they enrich the projects with more…
Read more about this product
3 Review
Innovation, keep pace with the times :Add Build on the power of Blynk to configure smart home automation and build exciting IoT project. Programmable learner kit for beginners and professionals: Perfect intro to programmable Arduino electronic and IoT robotics. Wifi programming and control: With ESP8266 WIFI Shield , you can remote control programming…
Read more about this product
3 Review
it is new WiFi+Bluetooth dual-mode development board based on ESP32 design, using PCB on-board antenna, with 2 high-performance 32-bit LX6CPU, using 7-level pipeline architecture, main frequency adjustment range 80MHz to 240Mhz. ESP32-CAM WiFi Bluetooth Board ESP32-CAM-MB Micro USB to Serial Port CH340G with OV2640 2MP Camera Module. HK-ESP32-CAM-MB…
Read more about this product
3 Review
Lead Length: about 30cm. Thermal conductivity (K): 15~16x10-3-W/°C cm. Model: SP1848-27145. Package includes: 2 X Thermoelectric Power Module. If You Are Not Satisfied with Your Purchase for Any Reason, Please Feel Free To Contact Us at the Buyer Center or Support Email, 24/7 Quick Reply.
3 Review
Product OverviewThe Waveshare High-Precision AD/DA Expansion Shield Board is an excellent addition for your Raspberry Pi, offering high-precision AD/DA functions. Designed to fit the standard Raspberry Pi 40PIN GPIO extension header, this expansion shield is compatible with various Raspberry Pi series boards as well as the Jetson Nano. With its onboard…
Read more about this product
3 Review
Complete Set: This kit includes LEDs, motors, buzzers, switches, photoresistors, transistors, etc. which are all basic items in electronics. This starter kit is ideal for beginners who want to learn basic electronics and as well as for professionals that are in need of basic electronic components for their advanced projects. The ESP8266 Module: The…
Read more about this product