🔥 SEEKONE Heat Gun Hot Air: Powerful and Versatile Heating Tool for Various Applications Review

Hello dear readers of the review "Industrial hair dryer for electrical Hot Air Gun". The fact that this is an industrial hair dryer can be stated with a stretch, size, power, and the tasks to be solved are too narrow. I bought this hair dryer on Aliexpress for electrical work, so it was positioned there as a hair dryer for working with heat shrink tubing. When I ordered this hair dryer, it seemed quite small to me on the site, I was going to carry it in my small tool box for electrical work…

Good hair dryer. I bought this to do bumper work on my car. It worked well and I worked non-stop for almost 2 hours with no issues. I haven't used any other attachments so I can't speak for them.

I was concerned about the handling and weight of this gun before receiving it. But it's easy for me and I have arthritis so I'm grateful for that. Definitely gets quite hot - I use it for pouring acrylics and working with resin in my work. Good buy and value for me.

Works very well, I am very, very satisfied. I could have sworn the temperature dial is marked backwards, if I'm not mistaken, hot and cold are toggled on the dial. I actually thought it broke at first because the temperature was so low, until I turned the knob the other way and it got as hot as expected. A fantastic buy though.

The heat gun works great. I will say that the temperature controller is easy to use, but it is easy to misunderstand at first glance. There is a triangle on the gun just above the temperature control knob. This might give the impression that the triangle is an arrow pointing at the dial to tell you what temperature you've selected. This would be wrong. When fully rotated, the triangle indicates the lowest temperature. When fully rotated, the triangle indicates the highest temperature. It took…

Have already spent several hours scraping a heavy coat of paint off the house. Requires the strongest heat but works well. Looks sturdy and comes with LOTS of attachments and scrapers (more than listed). A big improvement over my old one (which lasted 20 years but had a tendency to ignite wood chips). Better heat control; also a small wire stand to lean on while it cools. I have noticed that the fan/motor noise changes after a while after using it; It's probably a good idea to chill for a few…

While working on a project I needed to continuously wrap a 24" x 48" x 1/8" acrylic sheet" I initially settled on a smaller heating tool, but I struggled to heat a large area hot enough to get an even bend without lumps. Then I bought a SEEKONE 1800W heat gun and wrapped it up in an hour! Not only is this pistol customizable and well designed, but the support people work insanely fast and efficiently. I had an issue with an attachment and within 2 days of emailing support I had a replacement at

I work a lot with electronics, especially circuit boards. I often have to remove through components and sometimes desolder with a Hakko soldering iron and the solder pump just doesn't work and the part is very difficult to remove. I decided not to pay much for a cheap dedicated hot air reflow station and try a high temperature heat gun instead. It made a big difference. This heat gun can get so hot that the solder melts and I have to remove the component with tweezers while the solder is still…

I have been using this product for about a year without any problems. At this point I noticed the fan getting louder. I opened it up and cleaned it up a bit, made sure I reinstalled the fan properly, etc. After about a month it was back to normal. However, this morning I turned on the device and let it warm up (about five minutes). I started to feel something strange and noticed the nozzle started turning black and the plastic around the nozzle was melting. I turned it off quickly. I did a bit…

When you buy a heater you expect it to be safe, control temperature and work. This is in line with those expectations. It is also lightweight and easy to use. I also have to thank the seller for providing important information on the front page instead of burying it like others. There are a few minor issues: 1) The metal clip is listed as a stand. This can not be true. This would be unbalanced and the line would have to be twisted for it to break. Maybe it's a hanger, but wait. I wasn't…