Header banner
Revain logoHome Page
Janelle Simmons photo
Madagascar, Antananarivo
1 Level
495 Review
0 Karma

Review on ZIYOO Platform Strengthen Mattress Foundation by Janelle Simmons

Revainrating 4 out of 5

You can easily customize it yourself using my method. Even with 2 I would suggest following my method.

This will be my first night on this frame and I haven't really "tested" it yet. But overall I'm very satisfied. Two people can make this easier, but I managed it alone in about 45 minutes. 5 of them went in and out of the garage to get a wrench after the small wrench that came with it bent. I've been a mechanic for over 20 years, but it doesn't take much skill to do it on your own. I'll give you some tips to make it easier.1. Take a ring spanner for 13 and 10 mm. Don't use the Poc it comes with. The supplied Allen key is fine. It's nice and short so you don't accidentally twist the screw. Also, get a tape measure that is at least 12 feet long so you can level it before fully tightening the hardware. 2. After opening the box, take inventory and make sure you have all the parts.3. Place pieces A, B, C, D and both E in the center of the room. The side rails (E) swing out to extend. One side is straight, one side is beveled. Open the straight side first, then the conical side.4. When everything is laid out on the floor, set AD to E. Some of the holes are drilled really well, so make sure you can turn 2-3 threads by hand. This soft Chinese metal is very easy to remove. Install all screws freely. level, but with a slight wobble. Don't worry, you'll tighten them later. The head and greaves (F) run the same as the sides. Here you can easily do it with one person. Attach the rails and fully extend the non-tapered ends. And make sure both are facing to the left (when looking at the bed). Stand on the left rail (E) and lean it against it (F). Now let the tapered ends (F) (right side) hang down off the ground and act as supports. Be sure to insert both bolts before installing the nuts. DO NOT fully tighten at this point. Tight but slightly wobbly. Then lift the right rail (E) and attach it in the same way. Cozy nuts but leave room for maneuver.6. Assemble the main support (G) in place and insert all the bolts into the holes, then loosely fit the nuts.7. Well, that's where the roulette wheel comes in and why you hesitated a bit when it came to gear. Measure diagonally from corner to corner. When the dimensions match, you have a square and you can start tightening all the gear. Start with legs AD, then tighten nuts on F. Be careful NOT to overtighten the fasteners or they will break. German twist it, as we used to say. sealed. If your measurements are not the same from corner to corner, adjust the bed by sliding the bottom rail left or right until the measurements are the same. After they are even, tighten as previously discussed.8. With the rails in place, tighten the nuts holding the main support (G) in place. I intentionally rotated them a bit to sink the button heads under the side rails. Don't go too far, but getting them flush with the E-rails will help prevent some wear and tear on the mattress.9. Place the frame where you want it. With wooden slats it becomes difficult. Once in place, install the wooden slats. Note: The fins are approximately 1/2 inch shorter than the width between the brackets. So I tried to center them as much as possible. 10. Now it's time to put your fun pillow on the frame. Two people can help here. BE CAREFUL. The corners are sharp and if you pull the mattress over them you will most likely rip them! So. If you only have yourself, take some cardboard from the packaging and place it in the corners when you put the mattress back in place. One thing that I really noticed and liked about this bed is that the wooden slats are very smooth which makes bed placement very smooth. very light without snagging the mattress. Last note. I will order black pool noodles to wrap at least 4 of the 6 legs. The first thing I did after installing it was smacking my toe and it hurt! So I'm going to wrap my legs in black pasta and secure with some black zip ties.

Pros
  • Absolute Legend
Cons
  • Periodicity