These worked [as expected] for the price and reviews.I used these on my 03 Odyssey. They worked for the under front cover, and they only worked in the front main row, and not a few in the back, as I believe they are 8mm.Even though they are not the OEM Honda parts. I was able to buy 40 for the price of 1.5 clips.hahaOne thing that I found was: they had different shaft lengths. Some were an 1/8 longer or so than others. So I found the longest ones and used them.Even with the odd sized pins. I…

Works as good or better than the factory ones. I enjoy having these on hand to replace any that break during service. Thanks for attention.

I have a small shop that works on Hondas. I mainly use them on Pilots when i change the timing belts or have to remove the lower panel to access the transmissions pressure sensors although they work on any Honda that uses the 10mm rivet. I have been using them since 2016 and have seen them four or five years later and they are not brittle. I do use push pin pliers to remove and that does not break them. Even on the factory rivets, if you do not pull the center pin out evenly they will break…

These are too large for the Accord fender liners. They claim to be the right ones but the 10mm will only work on a few places on the bumper and splash shield. You need the smaller 8mm clips for the fender liners.

I liked the fact that there were enough of the fender clips so that if I broke one or two that I would have enough to finish the job. I did break one but had more than enough to do the job and have more for another project. I took off the front bumper of a 2003 Acura TL to replace the headlight ballasts and marker bulbs. It had been removed before and some of the clip holes were just held together with zip-ties. Looks much better now.

I have a Honda CRV 2014. These are a real tight fit. I couldn’t get them installed by hand, no matter how hard I push into the holes. I had to use a small screw driver to wedge them in. In hindsight, I could have slightly sanded them to fit easier. But once the center lock is pushed in, it is super tight.

Purchased these for my 02 CRV when I was doing some front end work.Some of the old clips fell out over time and I expected to break the others so I invested in these.These fit perfectly for the bumper and grill on the CRV.Some people complain that it is difficult to remove these and they will break upon removing. While it is true these are a little stiffer and you may break some here and there when you try to remove them, you have to remember is they are not designed for constantly removing and

First of all: overall these are good parts. They work well as replacements for the most common Honda body clip size and those clips often break once they get old.These aren't as strong as the factory parts and have no metal content at all, so I try to use the remaining not broken factory parts on the higher stressed areas (especially where two plastic panels meet with one metal panel) and use these on the lower stress areas.The other annoying thing is that these are listed as "40 PCS". That…

I bought these clips to replace some broken ones holding the boot in my wheel well. They were super cheap, and as expected since they came from China, they took a month to get here. That's fine. I was content to wait since they were so reasonably priced. They are of decent quality and if you're not in any hurry, you can't do better.Update: September 17, 2016 - So I finally got around to using them and unfortunately have to report that they did NOT fit the boot in the wheel well on our 2007…

I'm sure that these are a quality part, but they are the wrong size. The 10mm is way too large for my vehicle. So now I have parts nearly dangling because I had to spread around the factory clips that survived removal. I will find the correct size and order them tonight. Maybe I can give the 10mm rivets to someone who needs them.

I was doing repairs to my Honda Element and was removing the undercarriage cover. I already knew I was missing some Fasteners so I bought these. I ended up replacing ALL of the fasteners! Let me tell you, so great having all new fasteners, everything is tight and snug. They worked great! I recommend buying these to have on hand. Trust me your mechanic does not replace them when he breaks them. They are easy for you to change, especial if you buy the tool for 6 bucks.

Worked perfectly for a 2010 Honda Accord EX-L. Replaced the fog light.broke quite a few original clips when taking off the front bumper. It is not the exact same clip as the original, but these fit, and appear to function just as well.