🔍 Enhance Visibility and Stability: ATV Tek (UTVMIRCTR) Stable Clearview UTV Center Mirror Review

Will not fit the Yamaha Rhino as the upper roll bar is too far from the windshield. It must be clear from the product description that it does not work well on Rhino. The product is very well made; Easy to install and DOES NOT vibrate! I wish they made one that works on my rhino!

Bought a second mirror for my ranger. Decent quality and limited vibration. Good mirror for UTV. Installed it on my 2016 RZR EPS Trail. Ease of installation. Seems pretty solid and vibration is limited. Fits 1.75" tubes easily. Also fits smaller tubes from 1.5" to 2". Good quality mirror. I am happy with the purchase.

I have a Honda Poineer 500, I added the roof and pan along with the unit, once you use it you will notice what is missing, rear view mirrors and side mirrors, all for safe reversing in tree areas . This is a great device, installation was confusing until you've tried many combinations, the printed photo page is fuzzy, good value for money once it's finally installed.

Bought for my 2020 Honda Pioneer 700. A very good mirror. Yes, it's a bit more expensive than others, but you get what you pay for. This mirror feels and looks good and does not wobble while driving. The innovative attachment system can be adapted to almost anything. In general very satisfied. (If you can't tell)

Easy installation. Rubberized clamps hold tight (in my case the pipe is 1.75). Make sure you install the mount correctly (as shown in the product image) because if you turn it upside down it will still work but the ball and mirror mount will not have full range. It's easy to adjust the angle of the mirror. Holds reliably even when driving over bumps and potholes. You have to loosen the clamp screw to change the angle of the mirror when changing riders, which sits at wildly different heights…

Very strong. I have a Honda Pioneer 700-4 that says it has 1 3/4 bars but they are actually about 1 5/8 making the brackets 1 3/4 loose. For this reason I sent back another mirror. The design of this mount allows you to change the size of the bar at will. It has a padded yoke mount that can be tightened very securely with a flat head screwdriver. The mirror itself is more like a car mirror in size, with a slight curvature to offer a larger field of view. I have yet to really punish this mirror…

I like this mirror. It fit my 2016 Polaris RZR 900 XC perfectly and was easy to install. It works well and has very little vibration. I usually go ahead of the group we ride with and spend a lot of time looking back to make sure the next rider sees where to turn on tricky trails where it's easy to lose someone. This eliminates provisioning and simplifies backup. Haven't used it in very rough terrain yet, but it seems to be quite durable. I expect it to work fine. It is slightly concave and…

A bit difficult to rate on the selected questions as they don't really reflect why I returned them. I tried to install it on my 2020 Can Am Maverick Trail 800 but there is a 1/4 inch gap between the mirror mount and the roll bar (the mount is not designed for larger diameter bars). The alternate bracket has two screws for factory mounting, however these will deviate approximately 1/8" left or right and will require modification of the transom bracket or factory mounting holes. All the company…

When you buy a UTV or Side by Side, the very first accessory I recommend you buy is this mirror. You get tired of turning your head very quickly to see if someone is behind you or if the other drivers you are traveling with are ok. This mirror is very firmly attached to the bow with soft clips. This way you don't scratch the paintwork. The mirror arm itself is highly adjustable and can be positioned at almost any desired angle. The mirror itself sits on a rubberized ball, similar to a RAM…

Excellent quality mirror. The clamps have a lot of adjustment options which I needed when clamping the 1 1/4" rod. The reason for the 4 stars is that the clamping mechanism uses both the ball end where the mirror is located and the notched clamp/ Adjustment on the opposite end binds, so when the screw tries to tighten both sides at the same time, it can't tighten both sides evenly because it's in between them, and since the ball is too big an end, it tightens fine (which is good and the side…