🚗 Bosch 0261230234 Original Equipment MAP Sensor for Audi & Volkswagen Vehicles: A4, A5, A6, A7, A8, Q5, Q7, RS5, SQ5, S4, S5, S6, Beetle, Golf, Jetta, Passat, Rabbit, Touareg Review

I usually try to buy original sensors but I keep a few generic ones just in case. They work just like the original sensors, but you have to connect the original connector. DO NOT ATTEMPT TO SOLDER THE WIRES TOGETHER. The oxygen sensor wires are not made of copper. This is a special alloy that simply cannot be soldered. You must use the connector that came with the part or use heat shrink connectors. (assuming you have the correct crimping tool) https://www.youtube.com/watch?v=ex1Hki6-NHw This…

Will not fit ports on my 2003 BMW E46 325i M54 Sedan Manufactured in April 2003 THESE O2 SENSORS FOR 325I MANUFACTURED ON AND BEFORE DATE 3/2003. I think there is a year classification for the 325i in 2003. Others like mine were made after that date and use other O2 sensors and other miscellaneous engine parts I found out. For BMWs built after March 3rd you will need Bosch 15680 and 15681 downstreams (both will fit both downstreams). And for upstream you need Bosch 17215 and 17216 (both work…

If you're having trouble starting, poor acceleration, rough idle, black smoke out of the exhaust, or just have a horrible P0193 code, it's more than likely that the fuel line pressure sensor is dying and wanting to go through be replaced with a good new sensor. If the computer cannot determine the fuel pressure at the injectors, be prepared for a lean mixture in your combustion. In my condition, the Ford F-150 was running very rich with an incorrect reading of 11psi on the fuel rail…

Bosch makes good parts so I bought it without hesitation when I saw this unit. When I received my part today, it was installed in just a few minutes. I spent a little more time unplugging the power connector from the old part so as not to damage it. You need to place a small flathead screwdriver on top of the latch and push it down, then gently pry it off the connector. I also stuffed it with paper towels before removing it from the engine and I only opened it slightly until the pressure was…

If you have a Mercedes S Class (2000-2006) you should have this one. You should always have a spare part in the car because these things sometimes break without notice or with very little warning. This little Crankshaft Position Sensor (CPS) will leave you calm and dry in a deserted parking lot after watching a movie and having dinner on your first date. You proudly walk to your hundred thousand dollar car, turn the key and all you hear is, uh, uh, uh, uh, uh, noise. You know, the kind that…

This sensor fixed a starting problem on my 2004 3.2L V6 Crossfire! I am 43 years old and this part was very easy to install myself. My problems started after I drove into town one day. When I tried to start the car to get home, it kept overturning but wouldn't start. I waited a few minutes and thankfully it started up again. When I got home I parked the car and tried to start it and again it kept turning but wouldn't start. The next morning when the engine was cold it started right away, but…

Update: took 5 months - back to Denso I bought this for a 2000 Toyota Camry V6 as a BOTTOM FLOW sensor (after catalyst - rearmost sensor like V6 three sensors: two in front of catalyst and one after). First, Toyota is very sensitive to its sensors, which is why many people choose the Denso brand used by Toyota. That said, Denso sensors are at least twice the price, but they turn off the check engine light and last over 100,000 miles, which probably means a one-time replacement for most…

My car was bought with no records so I had no idea when they were replaced. My car hasn't given me any problems or codes, but as a preventative maintenance I decided to replace them. It was pretty easy, but it took a long time. The reason for this is that I used a crow's foot (22mm) instead of an O2 sensor socket. If you decide to buy an O2 sensor socket, make sure it is thick as the socket can bend if the O2 sensor is stuck very hard. The O2 sensor is located on the passenger side of the car…

My 05 S430 does not start the first time after a short stop. I ordered this part and installed it myself. 2 weeks and so far so good! The original part shows the BENZ and BOSCH part numbers, while this part shows only the BOSCH part number. Here are the rough removal steps after watching some good videos of yours. Pipe: 1. No need to remove the heat shield, just bend or push it down to give you more room to work with the E8 torx screw. I didn't do this when unscrewing the bolt, it was difficult