Header banner
Revain logoHome Page
๐Ÿ”ง dewhel manual gear shifter lever shift knob boot retainer/adapter - 12x1.25 (black) logo

๐Ÿ”ง Dewhel Manual Gear Shifter Lever Shift Knob Boot Retainer/Adapter - 12X1.25 (Black) Review

5

ยท

Average

Revainrating 3.5 out of 5ย ย 
Ratingย 
3.4
๐Ÿ•น๏ธ Shift Boots & Knobs, ๐Ÿš— Interior Car Accessories

View on AmazonView on ะฏM

Media

(4)
img 1 attached to ๐Ÿ”ง Dewhel Manual Gear Shifter Lever Shift Knob Boot Retainer/Adapter - 12X1.25 (Black)
img 2 attached to ๐Ÿ”ง Dewhel Manual Gear Shifter Lever Shift Knob Boot Retainer/Adapter - 12X1.25 (Black)
img 3 attached to ๐Ÿ”ง Dewhel Manual Gear Shifter Lever Shift Knob Boot Retainer/Adapter - 12X1.25 (Black)
img 4 attached to ๐Ÿ”ง Dewhel Manual Gear Shifter Lever Shift Knob Boot Retainer/Adapter - 12X1.25 (Black)

Details

ColorBlack
Handle TypeKnob
Metal TypeAluminum
Handle MaterialAluminum
BrandDEWHEL

Description of ๐Ÿ”ง Dewhel Manual Gear Shifter Lever Shift Knob Boot Retainer/Adapter - 12X1.25 (Black)

Thread pitch M12*1.25. Fit for most Manual Subaru Impreza , Susuki Samurai ,Toyota Supra 1993 -98 (JZ) ,Toyota MR2 1991-95 (SW20),Toyota Corrola,Toyota Celica-Tercel,Toyota Camry,Toyota Trucks,Geo tracker,Ford Mustang (Newer manual),Skyline (R34),Scion xA xB and tC(excluding Scion tC and xB 2008) etc. Made from aircraft grade billet aluminum. Takes up the space between the bottom of your shift knob and the top of your shift boot for a nice aesthetically pleasing affect. This shift boot retainer adapter will allow you to buy any aftermarket shift knob of your choice and say goodbye to your ugly OEM shift knob. The shift boot adapter is meant to be used on MANUAL Gear Shifter Lever TRANSMISSIONS (ONLY).

Reviews

Global ratings 5
  • 5
    1
  • 4
    2
  • 3
    0
  • 2
    2
  • 1
    0

Type of review

Revainrating 4 out of 5

Fits third generation Tacoma automatic transmissions

I have a 2017 trd off-road with an automatic transmission. I got a new shifter and the stock trunk latch didn't look good. I saw that it stood for a manual transmission and tried my luck anyway. By no means is it a tight and snug fit as you can take a new boot holder and move it up and down, but it did the job to my satisfaction of what I needed.

Pros
  • Stylish and modern design
Cons
  • New competitors have appeared

Revainrating 5 out of 5

Okay, Subarus needs some tweaking.

Nice little adapter. My only real complaint is that it will NOT fit Subaru Impreza boots without a small modification. I had to remove the rubber mount (which is easy since it's just glued on) and then secure it with a zip tie. Do not zip up before tightening as screwing in will cause back pain if the boot is screwed in first.

Pros
  • Decent performance
Cons
  • Useless features

Revainrating 4 out of 5

A must when installing post-launch shift knobs

I need this to hold my shift boot in place after replacing the stock shift knob. Pretty easy to install. Although the stock 2013 Subaru Impreza shift boot has a plastic ring that prevents it from going past the bottom edge of this bracket. I had to remove the console to access the shifter shoe and remove the ring. My spare boot isn't going anywhere now.

Pros
  • Easy to read control panel
Cons
  • Little repairability

In general I like the quality and the presence of metal adapters (everything else seems plastic). When I screwed it on (without the adapter) the metal insert came loose so I had to glue it back on. The color is deepened so I assume it won't rub off. No instructions. Just accept that you need to buy an adapter. I had to make a second purchase. DEWHEL Shift Knob Shift Knob Bracket/Adaptor 12X1.25 (Black) When I used the adapter, the new shifter was higher than the old one. It's ok, just FYI.

Pros
  • Stable results during testing
Cons
  • Could have chosen a newer model

Revainrating 2 out of 5

Assembly is not suitable for 2013 Mustang.

When I found this trunk lock I was very excited because it was so much cheaper than the American Muscle website and it was the perfect color match for my blue 2013 Mustang GT. . After seeing a description that said "new Mustangs" and a few rave reviews from people who had this installed on their 2013 Mustangs, the purchase was a no-brainer. But when I finally got it (it took 4 days for Prime 2 days shipping) and installed it definitely didn't fit. The thread was 12mm x 1.25 but the base of theโ€ฆ

Pros
  • Best in its niche
Cons
  • I will add later