Header banner
Revain logoHome Page
🌡️ inkbird itc-1000f 2-stage temperature controller with cooling and heating modes - celsius and fahrenheit logo

🌡️ Inkbird ITC-1000F 2-Stage Temperature Controller with Cooling and Heating Modes - Celsius and Fahrenheit Review

5

·

Very good

Revainrating 4.5 out of 5  
Rating 
4.6
🛠️ Scanners & Testers, 📏 Measuring & Layout Tools

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🌡️ Inkbird ITC-1000F 2-Stage Temperature Controller with Cooling and Heating Modes - Celsius and Fahrenheit
img 2 attached to 🌡️ Inkbird ITC-1000F 2-Stage Temperature Controller with Cooling and Heating Modes - Celsius and Fahrenheit
img 3 attached to 🌡️ Inkbird ITC-1000F 2-Stage Temperature Controller with Cooling and Heating Modes - Celsius and Fahrenheit
img 4 attached to 🌡️ Inkbird ITC-1000F 2-Stage Temperature Controller with Cooling and Heating Modes - Celsius and Fahrenheit

Description of 🌡️ Inkbird ITC-1000F 2-Stage Temperature Controller with Cooling and Heating Modes - Celsius and Fahrenheit

🔆🔆There are two relays. Switch between cooling and heating modes. Support for °F / °C display. 🔆🔆Overheat Protection of Home Appliances, hatching, Seedling pads, constant temperature Circulation and other Electrical Appliances. 🔆🔆By setting the temperature set-point and the difference between the temperature set-point and the difference. 🔆🔆Alarm when temperature is out of limit or sensor is wrong. 🔆🔆Switch between refrigeration and heating modes, temperature calibration.

Reviews

Global ratings 5
  • 5
    3
  • 4
    2
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

Perfect for my egg incubator at home.

I am using a temperature control unit for a quail egg incubator. So far it works great. Turn on at 99° and turn off at 100°. The accuracy of the thermostat is impeccable, it has been tested with three others. The installation instructions are good and clear. I hooked it up in ten minutes. Overall I am happy with this purchase, I would buy it again.

Pros
  • 🔆🔆By setting the temperature set point and the difference between the temperature set point and the difference.
Cons
  • Doubtful

Revainrating 4 out of 5

Not 220V as stated in the specs

Unit is rated for 110V ONLY, not 110/220V as shown in the diagram or 220V as stated in the specs. I bought it for a 220V car. Now we need to install the transformer. The customer wants the reading to be in F, the only other 220v devices are in C only. The seller must correct the description or purchase a 220v model that matches the description. Not satisfied, the transformer is more expensive than the block.

Pros
  • 🔆🔆Alert if the temperature is out of range or the sensor is wrong.
Cons
  • Hard to tell

Revainrating 5 out of 5

We use LOTS of it.

Be careful with this particular listing: the specs say 220 volts, it's not. THIS IS ITC-1000F at 110 volts. We have installed several hundred of these units and have no complaints, they are fantastic in most installations! Burden. The voltage on the CONTACTS can range from millivolts to 240 volts. The control voltage is irrelevant. (12/24/110)

Pros
  • 🔆🔆 Protection against overheating of household appliances, hatches, seedling pads, constant temperature circulation and other electrical appliances.
Cons
  • Exorbitant price

Revainrating 5 out of 5

BEST FRIDGE CONTROLLER FOR OLD TRUE

Ideal for an old commercial refrigerator. Breathed new life into an old TRUE commercial grocery store fridge. I had to modify the unit by removing the 10 amp cooling relay and connecting a 12 volt coil voltage to the terminal block so I could use a 40 amp solid state relay (SSR). The cooler draws 11 amps after startup, which would deactivate the built-in relay. I also put the sensor in a small bottle or in GLYCERIN to moderate the temperature when the door opens/closes. This helps to slow down…

Pros
  • 🔆🔆Alarm when temperature is out of range or sensor is broken.
Cons
  • old

Revainrating 4 out of 5

INSTALLATION NOTES (Hell!)

First: CONTACTS (heat/cool mode) DO IT AUTOMATICALLY. I couldn't get the thing to heat. Apparently, when you set any temperature, the device automatically activates (closes) the corresponding relay. (There is no "normally closed" connection. They are both open until they close) ON button (top left) - hold down (this turns the device on and off). )UP/DOWN (arrows)SET THIS TANG!: Press and HOLD SET (3 seconds)/then UP ARROW. (This arrow will scroll through the different parameters you can…

Pros
  • 🔆🔆Toggle between cooling and heating mode, temperature calibration.
Cons
  • Not as thick as other picks