🍺 RETRO-CHA Retro Cupholder in Charcoal - Ideal Go Gear Accessory for Your Convenience Review

I think the designer tried to do too much of what I wanted. was a simple design. It was almost impossible to adjust the two "clips" to hold anything. Although there appear to be instructions on the packaging this used/replacement item was not included and I had to force it open and after nearly breaking it was able to get it working. Like, like, something like. Haven't tried it on my car yet. He can return if I don't get the missing instructions.

The price is too high compared to the quality of the goods, but they do their job well. I haven't had any issues with them falling out of the cup holder or holding large cups unsteadily. I had a very hard time fitting them to the cup holder properly. The instructions are not clear at all. You have to lift that little black tab (it doesn't say anywhere) to adjust the bottom, then push back down to lock it in place. My tongue popped out a few times trying to attach it, but luckily I was able to…

Honestly this is the only thing like this on the market and you can tell if your car will work with it or not before you buy it. It held my drive, but it's very heavy and incredibly difficult to set up. My car has 4 rubber grips inside the holder for the drink to sink into, as the bottom is just 2 U shaped *too short* pieces, struggled to stay in place. I either had to dangle it overboard and possibly fall over or close my second-place finish in the cup. Now it's gathering dust in my closet…

I had two problems: the size of my car and the need for a large extension. I needed one big enough to hold a quart sized drinking jar, similar to a mason jar. Most of the ones I've found online have had the glass pulled up. Because of the size of my car and the space allotted, I knew it wasn't going to work. I needed something that opened up so I could lift the can from the side. As with several reviewers, finding the right size for the current cup holder was a challenge. The best part was…

This works great and securely holds my Ozark Trail glass 20 ounce Ozark Trail double wall vacuum cup. There are only three things to worry about, and they are all minor. First, there's a little trick to making it even fit. Other reviews talk about it. Second, for this reason, it's best to use this in a situation where you know you'll be using it for the same size drinks all the time. (Going from my glass to a can of soda, to a fast food drink, or to an iced coffee just doesn't work.) Third, I…

Oh my god I really like them. I use 64 ounces. кувшины для моих бутылок с водой (полученные по 5 долларов за штуку в местной сети под названием 5-Below), и я беру их с собой повсюду, поэтому очень важно, чтобы они не оказались на полу со стороны пассажира и полностью вне досягаемости от я steering. With these things I can spin like Mario Andretti and the cans stay in place (no matter how full or empty they are)! Fully adjustable to fit any size cup holder or drink/jug size (within tolerances)…

Bought for my wife. I bought FlynJ a long time ago at a truck stop and have always used it in my vehicles. We both use large vacuum cups to drink coffee. She took a drink holder and used it forever. Now it's broken and I glued it back but it's a smooth surface so the areas I roughed up haven't absorbed the glue yet. I would have tried a different adhesive but I googled the part number on the cup holder and it directed me to Revain. Don't know if there is a better glue. I looked it up but gave…

Unless you want to block the second cup holder and the console's design makes a secure installation nearly impossible. It only works with a perfectly round cup holder, no straight edges like the CRV. The materials are very thin and the top slider can get stuck on the bottom adjuster. I broke the latch off with very little force. This is a thin plastic tab that holds the cup holder in place by pressing down. It's not strong enough for what it was designed for. I saw some reviews saying it's not…