How to install new taillights on a classic car?
Installing new taillights is a great way to upgrade the look of your classic car. Here are the steps to follow:
Parts Needed
- New taillight assemblies for your specific make/model
- Basic hand tools - screwdrivers, wrenches, pliers, etc.
- Electrical tape
- Dielectric grease
Steps
- Disconnect the battery.
- Remove old taillight assemblies. This usually involves unscrewing any trim pieces and then removing the nuts/bolts holding the assembly in place.
- Disconnect the wiring harness from the old assemblies. Make note of where each wire went.
- Install new assemblies in reverse order, connecting the wires to the same locations as the originals.
- Apply some dielectric grease inside the electrical connectors to prevent corrosion.
- Secure the new assemblies with the proper nuts/bolts.
- Replace any trim pieces previously removed.
- Reconnect battery power.
- Test that all lights are working properly.
Be sure to refer to your vehicle repair manual for the exact steps applicable to your make/model. Allow sufficient time as working with electrical connections on older cars can sometimes be tricky. Take it slow and be methodical. With some patience, you'll have stylish new LED or custom taillights bringing your classic ride up-to-date.
Another interesting products
How to replace faded or broken taillights?
It's important to promptly replace any faded or broken taillights to maintain the safety of your vehicle. Here are the steps to follow:
Parts Needed
- New replacement taillight assembly for your specific vehicle
- Basic hand tools - screwdrivers, wrenches, pliers, etc.
- Electrical tape
- Dielectric grease
Steps
- Disconnect the battery.
- Remove the interior trunk panel to access the rear of the taillight assembly.
- Remove any screws, bolts, or clips securing the taillight assembly.
- Detach the wiring harness connector from the assembly.
- Install the new taillight assembly, attaching the wiring connector.
- Apply dielectric grease to the electrical connections.
- Secure the new taillight with screws/bolts.
- Replace the trunk interior panel.
- Reconnect the battery.
- Test that the new taillight works correctly.
Refer to your vehicle repair manual for detailed steps. Work methodically and don't force anything during disassembly. Installing a new OEM or aftermarket replacement taillight will restore proper visibility and keep your vehicle road-safe.
How to restore your vintage taillights?
Restoring faded, clouded, or cracked vintage taillights can really refresh the look of your classic car. Here are some tips:
Supplies Needed
- Fine grit (800+) sandpaper
- Buffing compound
- Clean rags
- Masking tape
- Clear coat spray paint
Steps
- Remove taillight assembly from the vehicle.
- Disassemble housing to access the lens.
- Clean lens thoroughly with soap and water.
- Mask off any areas not to be sanded.
- Lightly sand lens with sandpaper to remove clouding.
- Use buffing compound to further polish lens.
- Clean well and apply 2-3 coats of clear coat spray.
- Allow clear coat to fully cure as per directions.
- Reassemble housing and reinstall on vehicle.
- Test operation of taillights.
Be cautious when sanding to avoid damaging the lens. Take your time and work in stages for best results. The clear coat will seal and protect the lens from future clouding. Your freshly restored vintage taillights will look amazing!
How to upgrade your old taillights to modern LEDs?
Upgrading your outdated taillights with modern, bright LEDs can really improve the look of your vehicle. Here's how to do it:
Parts Needed
- LED taillight assembly designed for your make/model
- Basic hand tools - screwdrivers, wrenches, etc.
- Electrical tape
- Dielectric grease
Steps
- Disconnect the battery power.
- Remove the taillight assembly by taking out any screws/bolts.
- Unplug the bulb socket or wiring harness.
- Plug in the LED light wiring to your vehicle's harness.
- Apply dielectric grease to the electrical connectors.
- Mount the new LED assembly using the reverse steps from removal.
- Reconnect the battery.
- Test that the LED lights illuminate properly.
- Repeat steps for the other side taillight.
That's it! The install is very straight forward. Just take your time and be gentle with any plastic clips. Make sure the orientation is correct before tightening everything back up. Enjoy your bright, stylish LED taillights!
How to clean and polish clouded taillight lenses?
Over time, the plastic lenses on taillights can become foggy, clouded, and faded from UV exposure and dirt buildup. Here are some tips for restoring clarity and shine:
Supplies
- Mild soap and water
- Plastic polish and buffing pad
- Microfiber cloths
- Masking tape
- Toothpaste
Steps
- Remove taillight assembly and clean off loose debris.
- Use soapy water to remove surface dirt and grime.
- Dry completely with a microfiber cloth.
- Apply plastic polish to buffing pad and rub onto lenses.
- For really stubborn areas, use masking tape and toothpaste as a gentle abrasive polish.
- Remove tape and wash off toothpaste thoroughly.
- Buff lenses to a clear, brilliant shine with microfiber cloths.
- Reinstall freshly detailed taillights.
Taking the time to properly clean and polish your lenses can make dull, faded lenses look new again. Always avoid using harsh abrasives that could scratch the plastic. With some elbow grease, you can restore clarity and luster to your taillights.
Top products in 🔦 Car Light Covers
9 Review
How to customize your taillights with different colors or styles?
Customizing your taillights is a great way to add a unique look to your vehicle. Here are some tips:
Supplies Needed
- Taillight tint film or paint
- New taillight assemblies in desired style
- Masking tape
- Sandpaper
- Clear coat
Steps
- Remove taillight assemblies from the vehicle.
- Clean thoroughly with soap and water.
- For tint film - cut pieces to fit and apply to the lenses.
- For paint - mask off any areas and lightly sand before painting.
- For replacement lights - transfer wiring harness connectors.
- Apply 2-3 coats of clear coat over paint for protection.
- Allow paint/clear coat to fully cure before reinstalling.
- Install completed customized taillight assemblies.
- Reconnect wiring harnesses and test lights.
Always check your local regulations on modifications allowed. Take your time prepping and applying tint or paint. Custom touches like chrome housings or LED light bars can also personalize your taillights.
Express your creativity while staying road legal with custom taillight treatments.How to use your Amazon Prime to buy RAMPAGE PRODUCTS 8660 Taillight 1976 2006
Upgrading the taillights on your classic car with RAMPAGE PRODUCTS 8660 Taillight 1976 2006 is easy and affordable with an Amazon Prime membership. Here are some tips for ordering through Amazon:
Check eligibility
Make sure your Amazon Prime membership is active so you can take advantage of free 2-day shipping and other benefits. If not an active member, you can sign up for a free 30-day Prime trial.
Search for product
Use Amazon's search bar to find "RAMPAGE PRODUCTS 8660 Taillight 1976 2006" - be sure it is sold directly by Amazon or Rampage to ensure product authenticity.
Select options
Choose your preferred quantity and any other available options like color. Make sure it is the correct part number for your vehicle's make and model year.
Add to cart & checkout
When ready, add the taillights to your shopping cart. Proceed through checkout and select your shipping address. Amazon Prime members can choose free 2-day shipping.
Select payment
Enter your payment details. You can pay with a credit/debit card or gift card balance if available. Amazon's checkout is secure and encrypted.
Track order
Once your order is placed, you'll receive an email confirmation with tracking info. Check delivery status anytime to see when your new taillights will arrive!
With the convenience of Amazon Prime's fast shipping and reliability, you'll be upgrading your classic car's style in no time. Enjoy the easy shopping experience.
How To Install Rampage Products 8660 Taillight On A 1976-2006 Jeep?
Installing the Rampage Products 8660 Taillight on a 1976-2006 Jeep is a simple process that can be done without drilling. Here are the steps to follow:
- Start by unpacking the taillight guards and ensuring that all the necessary hardware is included.
- Clean the surface of the taillights to remove any dirt or debris.
- Align the taillight guards with the taillights and ensure that they fit properly.
- Secure the taillight guards in place using the included hardware. Make sure that the guards are tightly secured to prevent any movement.
- Repeat the process for the other taillight guard.
- Once both taillight guards are installed, check to ensure that they are properly aligned and securely attached.
That's it! With these simple steps, you can easily install the Rampage Products 8660 Taillight on your 1976-2006 Jeep and give it a stylish and protective upgrade.
What Are The Dimensions Of Rampage Products 8660 Taillight?
Here are the dimensions of the Rampage Products 8660 Taillight:
It is important to note that the dimensions may vary slightly depending on the make and model of the Jeep. It is recommended to refer to the product specifications or contact the manufacturer for more accurate information.
What Is The Shipping Weight Of Rampage Products 8660 Taillight?
The shipping weight of the Rampage Products 8660 Taillight is approximately 5 pounds. The following is a list of the shipping weight information from the sources:
It is important to note that the shipping weight may vary slightly depending on the seller and shipping method.
