Review on 📷 SLIK Mini Pro III Table Top Tripod: Compact 2-Section, Max 10" - Sleek Black Design by Lance Story

I just got a new DSLR so I bought accessories for it too. This was one of the items I chose. I used to have mini tripods and they were all fine, but in the past I've only had to deal with cameras like Point & Shoot which obviously have a lower profile and lighter weight. When I saw this one (and a few others) I was mesmerized by his style. There's no question that a lens-mounted DSLR is heavy and can (relatively) be front-loaded. I really didn't think any of the typical mini lenses would work based on my experience. This design seemed like a good gamble as it basically looked like an actual tripod. I was a bit hesitant about the price ($30 with shipping) but took a chance because $30 was a small amount at the time and a really cheap price to protect a DSLR. I got it today and played around with it for about half an hour. The camera I received was a Canon Rebel T4i and for "testing purposes" I put on the larger of my two lenses, which has a Tamron 70-300mm zoom that protrudes 7.5 inches from the camera body , when fully undressed, and weighs about 3 pounds, 1.7. Ounces (camera and lens). I couldn't be happier and I'm glad I bought this tripod. Of course I installed it in my kitchen where everything is flat, solid and relaxed. Tripod, I'm not going to take any big risks with my thousand dollar camera. I'm just looking for a safe place to quickly set up my camera when I need it, and a large tripod isn't practical. What. Pros: - Durable - If used with straight legs and a little common sense I'm not sure what would make it more durable. Here's a tip. Some have suggested that if you have a long/heavy lens you shouldn't mount it I agree, I also found that if you lengthen that leg (just the one under the lens) it makes the rig even stronger because it's that transfers weight back to the camera. In this configuration I was able to slowly press down on the lens and not tilt the tripod. functionality. Works very similar to any large tripod. The camera screws onto the plate and you rotate it where you want it and then you just lock it in place. Easy handling. It's not difficult and can be installed in probably less than a minute. may be an exaggeration, but not by much). Cons: - Width - It's wide as others have said (about a 10.5 inch triangle). but I use it with a heavy SLR that sticks out a lot. It's a solid structure. Physics dictates that the base should be wide. You don't know how to avoid tipping over without spreading your legs. This may not be practical in all situations, but dropping the camera is impractical. Never. - Leg Lock- The legs are not locked, they are simply spread in their natural (wide) position. This works fine but seems like you should be able to block them. Neutrals: - Price - Does it cost $30? the buyer decides. I think so, but I also think the build quality is on par with typical cheap tripods and you can buy them cheaper. Where is the value of this item? The legs seem to be 90% shorter and there isn't that much detail? I would buy it again, but I'm not sure if there isn't some kind of extrusion going on. - Build quality is comparable to typical cheap camera tripods. For what I'll be using it for, I agree, but it's not bulletproof. The biggest problem I have is that I think I have to be careful about over-tightening the knobs. I can tighten them without much torque, but I definitely feel like I'll hear a "pop" if I overdo it. " and that would be the end of the game. Problems - I wanted to fix a couple of problems I saw in some of the less than happy reviews. Someone said that the suction cup only works when the feet are in a weird position I'm not sure what they had in mind but I didn't have this problem The suction cup is at the bottom of the rod that adjusts the height of the camera It can be moved up and down by loosening the lock nut just below the swivel head install the feet loosen the shaft and install the suction cup it may not work at any height but if you can use it it is height someone complained that it's not very tall the top of the tray is 8.5" when fully extended. I'm not sure how high it needs to be, it's a "MINI" tripod. I have no problem with the height. Another reviewer says it's too heavy. Wait a moment? is just over 8 inches, all hidden. I think it's a little bulky for a mini, but I still blame it ayu for having to be big to protect the camera. I'm sure someone could come up with a design that would fit well, but at what price. The weight is absolutely no problem. All in all, I'm very happy with it and would buy it again. If I encounter any problems I will update. But for now, it's a neat little tool in a box or bag.