Header banner
Revain logoHome Page
🎯 ultimate precision: acrux7 cornhole boards drilling cutter logo

🎯 Ultimate Precision: Acrux7 Cornhole Boards Drilling Cutter Review

3

Β·

Very good

Revainrating 4.5 out of 5Β Β 
RatingΒ 
4.3
πŸͺš Hole Saws & Accessories, πŸ”ͺ Cutting Tools

View on AmazonView on Π―M

Media

(4)
img 1 attached to 🎯 Ultimate Precision: Acrux7 Cornhole Boards Drilling Cutter
img 2 attached to 🎯 Ultimate Precision: Acrux7 Cornhole Boards Drilling Cutter
img 3 attached to 🎯 Ultimate Precision: Acrux7 Cornhole Boards Drilling Cutter
img 4 attached to 🎯 Ultimate Precision: Acrux7 Cornhole Boards Drilling Cutter

Description of 🎯 Ultimate Precision: Acrux7 Cornhole Boards Drilling Cutter

6 Inch Hole Saw Material - HSS carbon steel & Bi-metal steel, with high wear resistance and high toughness, and higher hardness, increased service life. Convenient and Efficient- Double metal strips and HSS teeth can be sharp and quick opening, reducing the opening time. Heavy duty hexagonal center shaft for use with any 1/2" electric drill, no restrictions. Cutting diameter is 6" / 150mm, Opening depth is 1-3/16". Using Method- Gently plunge the bit until the hole saw scuffs the surface of the wood.Slowly plunge through the cut without pushing when the saw begins to cut. Once the hole saw plunge through the opposite side of the wood, stop the drill. Package: 1 pack 6-in hole saw, 1pack hex shank drill bit adapter, 2 pack extra drill bits, 1 x extra hex wrench. Wide Range of Applications- Cutting holes for plywood, thin iron board(within 3mm), acrylic board, gypsum board, ducts(water pipe, besides the stainless steel), ceiling lights, can light(not for hard cement board), Perfect for Corn Hole Board Drilling and other home projects.

Reviews

Global ratings 3
  • 5
    2
  • 4
    0
  • 3
    1
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

Quality saw for power and hand tools

For drilling holes in cornhole decking made from recycled decking. Before purchasing, I saw (pun intended) reviews of the saw separating and falling. This has happened to me a few times. But I did the job. I think the key is really pulling towards the drill, more than you think is enough. If you're like me and dragging things out too much to piss off your spouse, use that instinct here. The saw is strong enough, a good heavy tool. That's why I say again, turn on the saw. I've probably used this

Pros
  • User-friendly
Cons
  • Quick Start Guide

Revainrating 5 out of 5

Perfect for corn boards!

I made cutting boards and really didn't want to use a jigsaw to cut holes. I ended up getting this to make the job easier and OH BOY DID IT! My cordless drill/driver got through plywood with no problems. I even had to stop in the middle before it sank to take a picture simply because I was so impressed with how well and quickly it worked. This saved me tons of time and you can skip the compass by drilling a hole and sawing it out with a jigsaw or by hand. Just mark where I wanted to make the…

Pros
  • Stylish and modern design
Cons
  • Slightly wrinkled

Revainrating 3 out of 5

Cuts a clean hole but

I've never cut a 6" hole, this is my first 6" hole saw. I've used hole saws up to 4" in the past, so I'm not exactly a beginner. Not the sharpest bit I've ever used, tended to jam and try to yank the bit out of your hand. The first hole I cut I went straight through, it took a few minutes and the gap was bad. Luckily for me the crack was in the back of my corn board. The rest I have half done on one side and finished on the other side and the hole is cut clean. 4 holes in 3/4" thick plywood and

Pros
  • One year trial
Cons
  • Available in white only