Header banner
Revain logoHome Page
autex 1 pc 200 psi stainless steel pressure transducer: reliable pressure sender for oil, fuel, air, water, diesel, and gas logo

AUTEX 1 pc 200 Psi Stainless Steel Pressure Transducer: Reliable Pressure Sender for Oil, Fuel, Air, Water, Diesel, and Gas Review

6

·

Poor

Revainrating 3 out of 5  
Rating 
2.8
🔬 Automotive Sensors, 🛠️ Replacement Parts

View on AmazonView on ЯM

Media

(4)
img 1 attached to AUTEX 1 pc 200 Psi Stainless Steel Pressure Transducer: Reliable Pressure Sender for Oil, Fuel, Air, Water, Diesel, and Gas
img 2 attached to AUTEX 1 pc 200 Psi Stainless Steel Pressure Transducer: Reliable Pressure Sender for Oil, Fuel, Air, Water, Diesel, and Gas
img 3 attached to AUTEX 1 pc 200 Psi Stainless Steel Pressure Transducer: Reliable Pressure Sender for Oil, Fuel, Air, Water, Diesel, and Gas
img 4 attached to AUTEX 1 pc 200 Psi Stainless Steel Pressure Transducer: Reliable Pressure Sender for Oil, Fuel, Air, Water, Diesel, and Gas

Description of AUTEX 1 pc 200 Psi Stainless Steel Pressure Transducer: Reliable Pressure Sender for Oil, Fuel, Air, Water, Diesel, and Gas

Pressure transducer/sender/sensor 200 psi stainless steel for oil,fuel,air,water; 200 psi Pressure transducer/sender/sensor/Transmitter for oil/fuel/air/water; 200 psi oil/fuel/air/water Pressure transducer/sender/sensor/Transmitter Pressure Range: 0-200 psi, works for oil, fuel, water or air pressure. Can be used in oil tank, gas tank, etc. Output: 0.5V–4.5V linear voltage output. 0 psi outputs 0.5V, 100 psi outputs 2.5V, 200 psi outputs 4.5V. Package include: 1 pcs x200 psi pressure transducer. Pressure Medium: The gas and liquid which is compatible with 316L stainless steel; Electromagnetism Compatibility: EN50081-1; EN50082-2; IEC61000-4-3;. Please check the sensor before use: connect the 5V power to the sensor power supply, the multimeter modulates the voltage level, the red pen connects to the green wire, and the black pen connects to the black wire. The sampled voltage value tends to stabilize, then the sensor has no problem.

Reviews

Global ratings 6
  • 5
    2
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    3

Type of review

Revainrating 1 out of 5

Do not buy, gives wrong readings

The product looks good but the product description said it would read a maximum of 200psi, when I installed it it was over 200psi and I didn't even risk to blow up the compressor of this product did not work well at all

Pros
  • Perfect for outdoor activities
Cons
  • Quality

Revainrating 5 out of 5

Works well!: Pressure

I am using this to build a well water level monitor. I connected this to a Pex in a T configuration with this on one end and an analog meter on the other. This sensor is connected to an Arduino Nano clone and I can get stable readings that are consistent with an analog sensor.

Pros
  • Permanent test results
Cons
  • Requires socket

Revainrating 1 out of 5

Disappointed good for spares

I bought 2 to use with a PLC to control the water pressure. New, they read 10psi, both read 0psi. 1 lasted 1 month at 0-60psi. The other, which operates at 0-150psi, is currently still working. When it failed, it began to give off an unstable voltage. They don't seem to have a good failure mode. Don't use them for anything critical.

Pros
  • Quality construction
Cons
  • ---

Revainrating 1 out of 5

Don't save money for something that works

Once hooked up to my air traffic control to read my tank it got stuck at 70 pounds per square inch even when the pressure in the tank was 0 or 200 psi even after the compressors filled the tank, the gauge still read "70 psi". It was broken at the factory and did not serve its purpose, NOT RECOMMENDED

Pros
  • Certified
Cons
  • Cable is shorter than other picks

Revainrating 5 out of 5

Worked great: Pressure

I used this sensor to measure compression on a Mazda rotary engine. Used USB cable for +5V source (connected to USB charger). The colors of the wires are indicated in the description of this product. Worked very well when connected to an oscilloscope to measure the compression of each rotor. I used spark plug adapters from another compression tester I have. Also needed a threaded adapter socket I bought from Home Depot to match the threads.

Pros
  • Free for educational purposes
Cons
  • Not sure

Revainrating 4 out of 5

What does he want. - Sensors

braid is not long for much. I need to reconnect this connector with a sufficiently long cable. Otherwise, it is a visually appealing device. 1) The wiring is NOT waterproof although the connector is sealed. The diameter of the pigtail is smaller than the back shell of the connector. I'll have to add heat shrink tubing with glue to seal it or re-crimp the connectors on the cable I need to use. 2) It would be nice if it came as a kit where I could just plug in whatever cable I need. .

Pros
  • doping 🔥
Cons
  • expensive