Header banner
Revain logoHome Page
πŸ”‹ 2pack 9v battery clip connector cable with holder box for arduino uno r3 mega 2560 logo

πŸ”‹ 2Pack 9V Battery Clip Connector Cable with Holder Box for Arduino UNO R3 Mega 2560 Review

3

Β·

Poor

Revainrating 2.5 out of 5Β Β 
RatingΒ 
2.3
πŸ–₯️. Single Board Computers, πŸ’» Computer Components

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ”‹ 2Pack 9V Battery Clip Connector Cable with Holder Box for Arduino UNO R3 Mega 2560
img 2 attached to πŸ”‹ 2Pack 9V Battery Clip Connector Cable with Holder Box for Arduino UNO R3 Mega 2560
img 3 attached to πŸ”‹ 2Pack 9V Battery Clip Connector Cable with Holder Box for Arduino UNO R3 Mega 2560
img 4 attached to πŸ”‹ 2Pack 9V Battery Clip Connector Cable with Holder Box for Arduino UNO R3 Mega 2560

Description of πŸ”‹ 2Pack 9V Battery Clip Connector Cable with Holder Box for Arduino UNO R3 Mega 2560

Standard 5.5x2.1mm Center Positive Barrel Jack DC Male Plug. Cable length: Approx. 20cm (7.8 inch). Widely Used for Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, development boards, evaluation boards, breadboard, Arduino DIY, DSO 138 OscillOscope kit, XR2206 function generator and the device which need the 9V battery. Easy install & Save work: This cable come with a 9V battery holder and 3 screw fixing hole on the base, convenient for fixing; With this snap cable, you can saves the work of soldering a battery snap to a DC coax plug. Don't always have to take apart/open some test equipment just to change the battery inside. ! ! ! Not fit for Arduino Nano, Effect pedals. Any quality issues, please feel free to contact us.

Reviews

Global ratings 3
  • 5
    0
  • 4
    1
  • 3
    0
  • 2
    1
  • 1
    1

Type of review

Revainrating 1 out of 5

Ideal if you like the flickering PSU

Both were broken, each tested with three different fresh 9V batteries and it can be seen that the wires connecting the battery to the DC connector were not soldered well enough. Couldn't properly power a pathetic 5 inch LED strip with it. When I got power they would flicker like crazy, not as intended.

Pros
  • . If you have any quality problems, please feel free to contact us.
Cons
  • I'll write later

Revainrating 4 out of 5

3 mounting holes handy little thing

Nice little thing. I bought it to use with a tiny Donner reverb that doesn't have a battery box, but I want to make it portable. This is a wired position center so I cut and switched to the negative center common on guitar cabinets. Hey, sell both polarities!

Pros
  • ! ! ! Not suitable for Arduino Nano, effect pedals.
Cons
  • Band

Revainrating 2 out of 5

They will not work on single board computers

I ordered these because I liked the fact that they could be installed but they didn't even work, wasted almost $7, save your money.

Pros
  • Widely used for Arduino Uno, Arduino Due, Arduino Mega 2560, Arduino Ethernet Shield, Breadboards, Evaluation Boards, Breadboards, Arduino DIY, DSO 138 OscillOscope Kit, XR2206 Function Generator and devices that use a 9V battery require .
Cons
  • Weak Set