🔦 BEAMTECH H7 LED Bulb, 8000LM 40W Fanless CSP Y19 Chips 6500K Xenon White Super Bright Conversion Kit Ultra Thin All-In-One Halogen Replacement with Enhanced SEO Review

Nice and bright. It is very difficult to fit into the H7 light. The compression spring must be bent in order for it to work. The included H7 plastic adapter is too thick and doesn't have a slot to lock the clip in place. You won't burn out a lightbulb in the dashboard, but it will flicker when you check the lightbulb in the BMW.

I have a 2017 Ram 1500. All owners know or will know that the canbus system is very demanding. I've tried all sorts of sheaths, resistors, and wire harnesses to no avail. I came across the alph obd app and bought an obd reader that you plug into your car. This prompted the owner of the ram to turn on those headlights. The lights came on instantly, it took me 10 seconds to adjust them to a good sharpness. I have a light blue 6500k which is very bright and clean. I'd say they're almost as bright…

I installed them on my 17 Kawasaki Versys 1000. Installation isn't easy, but it's a car design issue, not a bulb issue. I can't say anything about durability yet. I was a bit skeptical because in the past the manufacturer showed the performance of LED car headlight bulbs completely unintegrated. But I decided to give it a try after hearing that advances in this technology had been made. Wow! Doesn't matter! Not only from factory halogens, but also from Sylvania Silver Stars, which I switched…

Purchased to replace bulbs in a 2014 Ninja. Earlier lamps were very dark even with high beam. These LED bulbs provide a bright white, even light pattern, a significant improvement over the old dull yellow halogen bulbs. Can't comment on durability/durability as they've only been installed for a week, but I have no complaints in that department yet. The only problems related to the installation; The OEM metal spring clips that hold the bulb in place had to be modified (bent) slightly to…

Seems like a solid product but I haven't had a chance to see if they work. The good folks at Volkswagen decided to create a weird proprietary lighting outlet to make a simple maintenance task more complicated than necessary. I can only assume that this also applies to the more manual variants of the Golf. The GTI I'm talking about comes with standard halogen headlights. I asked a question and received an affirmative answer. Unfortunately I was disappointed. The return process has started. I…

Definitely a good buy! I spent about $30 on it on my 2010 Ford F250 and it was the best $30 I've ever spent on headlights. I have aftermarket builds that support H7 low beams so obviously preferred these over the factory models. That being said, the new lights are a projector-style construction with a different look for the lights themselves. The LED lights themselves are very conservative in mass, which is nice. Easier gear hiding. With that in mind, I had to make small changes because I…

I have replaced my high and low beam bulbs with Beamtech. I haven't adjusted the height of the beam yet, but I can see further than before. The beam is white and I see it earlier than before before sunset. I don't want LED headlights that have a fan opinion that this is a point of failure and I'm very happy to find them. Where my low beam mount is very tight because the sheet metal is very close to the back of the housing, they fit perfectly. When I first put them on I took a night drive across

Installed on a 2011 Subaru Outback, each lamp took about 40 minutes to install, mainly because Subaru makes access difficult. I tested the lamps on a laboratory bench for about 5 hours before installing them. Here are some infrared images after approx. 2 hours outdoors at a room temperature of 20°C. Definitely not as hot as halogen, but it's important as 142C is slightly higher for long-term reliability of LEDs. The lamps did not draw the nominal 20 watts as stated. One lamp consumed 15.4 watts

I installed them as high and low beams on my Mercedes Sprinter (2016). They fit into the dust cover without any modifications to the case. It took some research to find the right adapters! No one seems to be selling adapters specifically for this car. High beam clamps are part number B07Q7WQ3SG which you simply install by rotating the alignment tab 180 degrees. The low beam adapter, part number B07N83PWDY, requires MUCH more work. This lamp assembly has a completely different connection to the…