Header banner
Revain logoHome Page
🔧 enhance your stepper motor control with bigtreetech tmc2208 stepper motherboard - bundle of 5 logo

🔧 Enhance Your Stepper Motor Control with BIGTREETECH TMC2208 Stepper Motherboard - Bundle of 5 Review

3

·

Average

Revainrating 3.5 out of 5  
Rating 
3.7
🖨️ 3D Printer Parts & Accessories, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🔧 Enhance Your Stepper Motor Control with BIGTREETECH TMC2208 Stepper Motherboard - Bundle of 5
img 2 attached to 🔧 Enhance Your Stepper Motor Control with BIGTREETECH TMC2208 Stepper Motherboard - Bundle of 5
img 3 attached to 🔧 Enhance Your Stepper Motor Control with BIGTREETECH TMC2208 Stepper Motherboard - Bundle of 5
img 4 attached to 🔧 Enhance Your Stepper Motor Control with BIGTREETECH TMC2208 Stepper Motherboard - Bundle of 5

Description of 🔧 Enhance Your Stepper Motor Control with BIGTREETECH TMC2208 Stepper Motherboard - Bundle of 5

1.【Good Heat Dissipation】: Large heat dissipation area, good heat dissipation effect. 2.【Ultra-quiet】: Stealth Chop can driver the motor to work under extreme silence. 3.【Avoid losing steps and Jittering】: Spreadcycle: The motor controlled by the PWM choppermode operated more smoothly and without Jitter. 4.【TMC2208 V3.0 Features】: ※Working Mode: Dir Step ※Microplver: 1/256 ※Microplyer Mode: Up to 256 ※Driver Current: Up to 2A ※Input Voltage: 4.75-35VDC ※Logical Voltage: 3.3V-5V ※Decibel: <10dB ※RDSON: ≤0.3Q ※Stealthchop(quiet): Yes ※Spreadcyle: Yes ※Motor Phase Current: 1.2A RMS, 2.0A Peak.

Reviews

Global ratings 3
  • 5
    2
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    1

Type of review

Revainrating 1 out of 5

Not in UART mode - Additive Manufacturing Products

It is difficult to tell from the description whether they refer to "Legacy" or "UART" mode. The manual says that they come from the factory in both directions and that the UART mode does not require setting J2 for UART mode. They are delivered without a configured J2! BigTree-Tech expects the customer to install a 0.4mm solder pad partially covered by the pre-installed headers.

Pros
  • Eliminating lost steps and jitter
Cons
  • Legacy model

Revainrating 5 out of 5

Amazing update for my I3 Mega

I ordered 5 of these to update the standard drivers in my Anycubic I3 Mega (was previously updated with the Mega S upgrade kit). Now the machine is so quiet that when I started typing I thought the extruder wasn't working at all. The ONLY sound coming from it at the moment is the fans and I need to work on upgrading them as well as some MOSFETs to run the greenhouse and heater more safely.

Pros
  • Ultra Quiet
Cons
  • I don't remember but there was something

Revainrating 5 out of 5

On to Steppin! best products for additive manufacturing

Ender 3 Pro + SKR v1.4Turbo + TCM2209 stepper driver = 1 amazing printer! from EeeEEeEEeeee sounding motions to Wooooosh Wooooooosh hahahhahahha Read the instructions carefully, you may need to cut the pin off the driver board. However, it is not difficult. The included thermal synchronizers do the job really well. I did a few prints that took several hours with no cover on the component case, so no fan. The printer has never been turned off due to overheating. As long as you update the…

Pros
  • Good heat dissipation
Cons
  • Big and bulky