Header banner
Revain logoHome Page
πŸš€ enhance ls engine performance with the ict billet ls drive by wire throttle body adapter logo

πŸš€ Enhance LS Engine Performance with the ICT Billet LS Drive By Wire Throttle Body Adapter Review

5

Β·

Average

Revainrating 3.5 out of 5Β Β 
RatingΒ 
3.6
πŸ›’οΈ Fuel System, 🏎️ Performance Car Parts & Accessories

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸš€ Enhance LS Engine Performance with the ICT Billet LS Drive By Wire Throttle Body Adapter
img 2 attached to πŸš€ Enhance LS Engine Performance with the ICT Billet LS Drive By Wire Throttle Body Adapter
img 3 attached to πŸš€ Enhance LS Engine Performance with the ICT Billet LS Drive By Wire Throttle Body Adapter
img 4 attached to πŸš€ Enhance LS Engine Performance with the ICT Billet LS Drive By Wire Throttle Body Adapter

Description of πŸš€ Enhance LS Engine Performance with the ICT Billet LS Drive By Wire Throttle Body Adapter

This throttle body adapter will allow you to install a 3-bolt DBW LS throttle body onto a 4-bolt LS intake. For example, an LS2 or LS3 intake manifold. Compatible with up to 75mm throttle body. Compatible with intake manifolds up to 102mm. Does not work with 3-bolt drive by cable throttle body or LS4 intakes. Natural finish aluminum as shown, includes mounting hardware and gasket.

Reviews

Global ratings 5
  • 5
    2
  • 4
    1
  • 3
    0
  • 2
    2
  • 1
    0

Type of review

Revainrating 2 out of 5

Fits LS Gen III DBW throttle body to Gen IV intake manifold

I upgraded a 2007 TBSS intake manifold on my 2005 Chevy Tahoe. This plate makes it easy to install and reuse a Gen III throttle body assembly on a Gen IV header like that on the Trail Blazer SS.

Pros
  • Best
Cons
  • Available in black only

Revainrating 5 out of 5

Good product: spare parts

Good product, works as it should. I wish the screws were a little longer, but I'm pretty sure you can't make them much longer with the thickness of the board.

Pros
  • Compatible with intake manifolds up to 102mm
Cons
  • Expensive

Revainrating 5 out of 5

This is ideal for installing a 3 bolt DBW throttle body on a .

To fit DBW 3 port throttle body to 4 port intake manifold. The throttle works smoothly in the fully open and closed position.

Pros
  • Natural painted aluminum as shown including fasteners and gasket
Cons
  • Operating speed

Revainrating 4 out of 5

Works, but make sure the gasket is facing the right direction to avoid a vacuum leak.

Works well but the screws are too short and the gasket does not fit properly causing a vacuum leak. Instead, I used rubber sealant. Works great until I get my 90mm choke.

Pros
  • This throttle body adapter allows you to mount a 3-hole DBW LS throttle body to a 4-hole LS inlet valve. For example intake manifold LS2 or LS3.
Cons
  • Nothing

Revainrating 2 out of 5

May be for other applications but for TBSS with NBS TB will not work

3 bolt DBW TB too close to water inlet stub TBSS. This can be corrected by increasing the screw position by 1/4 inch. Also, the gasket doesn't fit close to the back of the TB. Also, the screws for TB are short and only grab about 3 threads.

Pros
  • Will not work with 3 bolt actuator with cable restrictor or LS4 inlets
Cons
  • Too many