Dulytek DM800 Personal Heat Press Machine - 1350 Lbs, 2.5" X 3" Plates & Accessories Review

Ordered the dm800 bundle and just received the machine in a damaged state that also appeared to be used. The control panel on the back of the machine was peeling off the unit, the top plate is not even to the bottom and appears to swivel although it should not. The top and bottom plate had spots in the center showing signs of previous use. Was not purchased as used/refurb. Item was well packed in styrofoam.

1. The pressure is not sufficient for anything2. When you press the plates down they twist causing the parchment paper to tear causing if any product to leak out.and when you barley get anything to begin with you will be quite mad!3. After pressing with all your might you will notice the plates do not sit flat where your product is. 1side will have 1/16in gap compared to the side that is touching.plates should be flat with equal pressure to get a good squeezI looked at all the reviews of this…

I am really loving this press. It's heat settings are on point. The company included all the tools need to help make the most out of their press like a mini party pack. Shipping was faster than expected. Over all I'm supper stoked. Great buy for the price no money wasted.

Extremely difficult to push handle down, even more difficult to pull it up when timer goes off, had to find a breaker bar to make it easier. The power cord to the press would come loose while trying to use causing the machine to kick off. It also did not come with any accessories, yet the seller did email us saying sorry they're sending them no extra charge. Nice product just not sufficient nor easy to use

Broke handle in under 6 months. Highly recommend any press that is hydraulic. Don't waste your money.I like this press but I don't love it. It becomes a lot of effort if you want to get the most pressure that you can out of it. And trying to apply all that pressure has already caused the top plate to start to spin a little bit when you push down on it making it not even with the bottom plate any longer. It works though. Makes some really good resin out of good flower around 190° for about 65…

This is my first rosin press and I'm very happy with what I got for how much I spent. I didn't even know the two plates could be set to two different temps until I was reading the manual; Which was very easy to understand and had a good amount of beginner info. The included kit with magnets, picks, and silicone mat really came in handy! This little device really packs a punch. A few things were a little loose but with some tightening and adjusting, I have it working great! Just did my first…

Works great but do not expect a big yield from a smaller press.I love this thing i’ve used it over 30 times, only wear i see is the lever, maybe it needs to get lubricated with wd40 or some oil because it does get stiff, depending on how much squeeze you want, you have to pull the lever down.I will show you a picture, this area gets kind of "STUCK” in place and you have to press on certain points to get it to press down. I believe i put too much pressure trying to get as much squeeze as i could

I worked for only about 2 times then the display started to flash on, off, then it just stopped coming on. Now I cannot see what my temp is and cannot adjust anything. It beeped a few times and it was a struggling beep then it just dies. If I turn it off then turn it back on again the display will show up for about 1 second then disappear again.Update: I returned it no problem and got a new one. It works great so far.

I loooove this product! I did learn the hard way that pressure is just as important as heat. If you are not getting a good yield (25% return) it may be because you are not pressing the nug down hard enough. Make sure you can barely get it into locking position for best result. 220 degrees for 90 seconds 👌

Broke after a dozen presses. Tried to contact Dulytek customer support, no response after 3 days. Found a way to fix it myself, but will not recommend or buy their products again.

The pressure mechanism is not strong enough and cannot achieve adequate pressure without bend. The heat plate work well though under a hydraulic cylinder.

Not enough pressure for proper extraction. Plates are too small for any sizable extraction beyond a single use product extraction from 3.5 g

Kind of disappointed overall with this press. Does it make rosin? Yes.But it becomes very hard to get a good amount of pressure from. After my fourth press the top plate spun out of place so it doesn’t fully line up with the bottom plate. Something bent and I can’t bend it back. It’s a real shame. Buyer beware.

I like this press. It's simple to use and sturdy. Obviously, for small, personal use amounts. There is no pressure gauge, and it's not a 'high pressure' press. Works well with 2 or 3 grams of flower or non-solvent extract. DO NOT to use a filter bag when pressing flower. Half your press will get left behind.

It’s easy to use it took me 2 try’s to get it perfect! I would definitely recommend this machine to anyone looking for this.

The machine is good for the price but it says that you get a bonus starter kit but I didn’t get mines. The point of getting this one was because of the starter kit. Overall the machine works great and the delivery was fast.

This is a great little rosin press for personal use I was looking into getting a caged heat plate setup but it was just going to be too big and noticeable this thing is perfect to keep on my desk and when I have to it's easy enough to put up without it being a problem.

Product arrived 3 days sooner than expected. Everything works great and my first ever press gave me a 20% return. The press is difficult to operate.

Great press - simple to use, and solid yield from fresh flowers. Concentrates are tricky to find for us so this was absolutely perfect for our small batches.

Just buy this if youre new and dont know what to get starting out. This works excellent. Use Resinous buds at 200 and heat for a couple of minutes and BAM. Dont use bags as they soak up all the rosin with this small of a press. 3 or 4 runs will get ya a gram of good dab or so.