InstallGear 100A 4/8 AWG AGU Fuse Holder Distribution Block - 4 Gauge In To (2) 8 Gauge Out For Auto, RV, Motorcycle & Boat Review

This unit worked great. I use true 4 awg in but true 6 awg out. It's oxygen free stranded copper and I thought I might have to bore out the two 8 awg blocks to fit it but it was just big enough to fit. Made for a good tight fit. Mounted easy and looks really good. I replaced the 60 amp fuses with 50 amp since my amps are only one 500 watt rms mono and one 4 channel 75 watt rms. The only con would be at the input. The two side holes are not a good idea since it keeps the stranded wire from…

I used this to power a set of dual compressors for my air horns on my truck. Works perfect to reduce and split, went from 4ga to 2 8ga. Super easy to use, I like how you can put the input from different directions if you want. It allows for flexibility in mounting as well as helping with keeping the wiring neat.

I received this order with two 60amp fuses which i didn't realize was about 60amps more than my system requires. The seller sent me 4 30amp fuses for free. I appreciate when sellers do this kind of action on a product. The Fuse/power distributer is well made and works great in my system. Thanks again.

Nice block to split a 4 gauge power cable to 2- 8 gauge cables .The 4 gauge input can be done either strait in or at 45 degree angle- on side or other. Then the 2 8 gauge strait out . Makes for easy instal of this block

Does what it's supposed to do, but beware! A couple of the screws on the underside that hold the fuse holder to the metal block where the wires go were loose on mine. Didn't notice until installing it and a day later, one of the amps is not turning on and you can smell / hear the sparking from this distribution block because of the loose connections. All in all, a decent unit, but I would strongly recommend checking the screws that hold this thing together and using a thread locker to keep them

Good & fast deliver . I can't believe it the price of these fuses holder it has a good quality nice look I recommended a hundred percent

In the product details it states that you will receive 2 60 fuses with this product. I receive my package yesterday and did not get any 60 fuses with this.

InstallGear is identical to the ZOOKOTO chinese brand, right down to the screws used to hold the individual pieces of the fuse holder together. Yes, screws assemble these fuse holders, and not to the base. to each other. There is not enough positive contact surface between the individual components such as what you would get with welding or soldering them together to prevent high resistance under high load. This thing advertised 60 to 100A rating but any more than 40 amps constant would cause…

The fuse holder seems to be built very well. The design is very attractive. Can't comment on performance yet, have not done the install yet.

Looks nice at first glance. Material used and the connection between the buss and the fuse holder are very poor. Melts with less than 30 amps of draw.so So far from the old Stingers it's sad.

Good distribution fused block, you can actually get a #2 wire on the input side and #6 on each of the two outputs. Nice to have the two side holes on the in to help with connection angle but would have liked to see some type of block off plate for the unused ones, bare metal with that much amperage running to it just sitting there begging for a wayward screw or some other conductive materail makes me nervous, I cut some clear plastic to cover the two unused holes. They didn't have a 50amp…

It's very heavy duty. The back of it to insulate it from metal is thin. I will put some flex seal tape on it. I would buy it again.

Super easy to install and use. Ended up using zipties through the screw holes for my install and it wasn't an issue. I like that it accepts the input wire from all 3 sides. Outputs fit my oversized 8awg without issue. Quality of the parts and finish on the metal was higher than expected. Only downside is that when screwing down the wire, the output blocks felt a little unstable and may break if you torqued on it too much, so use caution when you do.

Feels solid. Terminal set screws feel like they're nice and tight. The clear cover snaps closed nicely. Fuses snap in the slots sevurely.

Great product. This fused distribution box is exactly what I needed to finish my install. Best thing about this unit is that the 4 gauge wire input has three slots giving me the the best possible angle for installation. Love it.

I have a 2009 G8 GT i used this for the new battery i put in and removed the old inline fuse box thing thats factory,with this it worked perfect