Header banner
Revain logoHome Page
otuayauto camshaft position sensor - replacement for chevy/gmc/cadillac/hummer/pontiac - fits 1999-2007 vehicles - oem 12561211 logo

OTUAYAUTO Camshaft Position Sensor - Replacement for Chevy/GMC/Cadillac/Hummer/Pontiac - fits 1999-2007 Vehicles - OEM 12561211 Review

4

·

Terrible

Revainrating 1 out of 5  
Rating 
1.0
🔬 Automotive Sensors, 🛠️ Replacement Parts

View on AmazonView on ЯM

Media

(4)
img 1 attached to OTUAYAUTO Camshaft Position Sensor - Replacement for Chevy/GMC/Cadillac/Hummer/Pontiac - fits 1999-2007 Vehicles - OEM 12561211
img 2 attached to OTUAYAUTO Camshaft Position Sensor - Replacement for Chevy/GMC/Cadillac/Hummer/Pontiac - fits 1999-2007 Vehicles - OEM 12561211
img 3 attached to OTUAYAUTO Camshaft Position Sensor - Replacement for Chevy/GMC/Cadillac/Hummer/Pontiac - fits 1999-2007 Vehicles - OEM 12561211
img 4 attached to OTUAYAUTO Camshaft Position Sensor - Replacement for Chevy/GMC/Cadillac/Hummer/Pontiac - fits 1999-2007 Vehicles - OEM 12561211

Details

BrandOTUAYAUTO
MaterialLead
Specific Uses For ProductCamshaft Position Sensor,Crankshaft Position

Description of OTUAYAUTO Camshaft Position Sensor - Replacement for Chevy/GMC/Cadillac/Hummer/Pontiac - fits 1999-2007 Vehicles - OEM 12561211

Fitment: Compatible with Chevy 03-07 Express 99-07 Silverado 00-06 Tahoe, GMC 03-04 Envoy 00-06 Yukon 99-07 Sierra, 02-06 Cadillac Escalade. Meets Or Exceeds OEM: 12561211, PC273, 8125612110, 5S1253, SU1277. High Quality: The Sensor made for highest standards materials, 100% undergo a strict quality tested before shipping. Feature: Direct replacement for the factory part, Sensor sleeves help protect wire leads from heat. Use: When the Crankshaft Position Sensor fail it can lead to vehicle intermittent stalling, CEL comes on, uneven acceleration, engine misfires or vibrates, then you will need it.

Reviews

Global ratings 4
  • 5
    0
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    4

Type of review

Revainrating 1 out of 5

Waste of time and money

Camshaft sensor didn't work at all My car didn't start well and failed because of cheap camshaft sensor new sensors are crap

Pros
  • Good thing
Cons
  • No paint needed

Revainrating 1 out of 5

Bad product: Sensors

I have replaced the inlet gasket on my 5.3 and the camshaft sensor with your product, otherwise you will not get to it. After installation, the car did not start and work well. Took the intake manifold back out and put the original sensor in and the car ran fine. Very disappointed

Pros
  • Lots of positive emotions
Cons
  • A little change

Revainrating 1 out of 5

Buy OEM, get rid of the headache

I have a truck with one of these. Assuming it was a bad sensor I bought the same one, it still outputs p0342. I started tracing the wires, checking for continuity, checking the waveform on the oscilloscope, everything looks fine. I installed the original 234,000 mile sensor from a junkyard engine and the error was gone. Save yourself the headache and get a real sensor.

Pros
  • understandable even for the old ones
Cons
  • Useless functions

Revainrating 1 out of 5

Set the error code within 20 minutes.

Failed inspection after sensor installation. If the crash is due to CPU overtraining I will update. The Tahoe is currently difficult to start and has never had this problem since its release. The weird thing is I only changed the sensor because it's almost impossible to replace without removing the intake manifold and I had the manifold removed to replace the knock sensors. Unfortunately, most of the parts I have purchased for my Revain Tahoe over the past 4 years have been defective or not as…

Pros
  • Stable test results
Cons
  • A newer model could have been selected