Header banner
Revain logoHome Page
high-temperature spark plug boot shields - 1800 degree heat shield insulator sleeve for car and truck, 6 inch spark plug wire boots (pack of 8) in titanium finish logo

High-Temperature Spark Plug Boot Shields - 1800 Degree Heat Shield Insulator Sleeve for Car and Truck, 6 inch Spark Plug Wire Boots (Pack of 8) in Titanium Finish Review

6

·

Poor

Revainrating 2 out of 5  
Rating 
2.2
🌫️ Exhaust & Emissions, 🛠️ Replacement Parts

View on AmazonView on ЯM

Media

(4)
img 1 attached to High-Temperature Spark Plug Boot Shields - 1800 Degree Heat Shield Insulator Sleeve for Car and Truck, 6 inch Spark Plug Wire Boots (Pack of 8) in Titanium Finish
img 2 attached to High-Temperature Spark Plug Boot Shields - 1800 Degree Heat Shield Insulator Sleeve for Car and Truck, 6 inch Spark Plug Wire Boots (Pack of 8) in Titanium Finish
img 3 attached to High-Temperature Spark Plug Boot Shields - 1800 Degree Heat Shield Insulator Sleeve for Car and Truck, 6 inch Spark Plug Wire Boots (Pack of 8) in Titanium Finish
img 4 attached to High-Temperature Spark Plug Boot Shields - 1800 Degree Heat Shield Insulator Sleeve for Car and Truck, 6 inch Spark Plug Wire Boots (Pack of 8) in Titanium Finish

Description of High-Temperature Spark Plug Boot Shields - 1800 Degree Heat Shield Insulator Sleeve for Car and Truck, 6 inch Spark Plug Wire Boots (Pack of 8) in Titanium Finish

【Fit】This universal spark plug boot protector can fit most angled and straight boots,Can be used from ultimate race cars, street vehicles, to motor homes.Length:6"(15.5cm) ID:1"(22mm). 【Function】Spark Plug Wire Boot Sleeves look great, helps reduce misfires,Resists damaging chemicals, extends life of wire & boots.non-flammable & protects against chemicals & resists water, Protect spark plug boots and spark plug wires from Excessive Engine and Exhaust Heat. 【Easy Installation】Just Slip On (Sewn End Over Spark Plug ) For Maximum Protection, Spark plug boot heat socks Can Withstand Heat rated for 1800°F continuous use, 2500°F intermittent.Spark plug boot heat socks, protect your expensive plug wire set’s performance and increase their lifetime. 【Compatibility】8pcs spark plug boot protector, Made From Double Wall Braided Fiberglass Sleeving, keep your spark wire and spark plug cooler in a high temperature environment,Constructed with double layered,they create an effective non-flammable thermal barrier that will extend the life of your ignition wires. 【Superiority】Each universal Spark Plug Wire Boots is 6inch Length, Boots Will Work With 90 Degree, 45 Degree, And Straight Spark Plug Boots, Set of 8 Spark Plug Wire Boot Sleeves,Made From Double Wall Braided Fiberglass Sleeving (Triple Wall At Sewn End).

Reviews

Global ratings 6
  • 5
    1
  • 4
    0
  • 3
    1
  • 2
    1
  • 1
    3

Type of review

Revainrating 3 out of 5

Very expensive but a must.

Installed connectors on my 57283. Without these boots I would burn wires all the time. No problem installing these boots.

Pros
  • Absolutely amazing!
Cons
  • No power

Revainrating 5 out of 5

Too much compared to what they want Brown's score

They are very easy to install. I removed the boot and threaded the spark plug wire through, then put the boot on. I found it too tight to try and put on a 90 degree feather duster.

Pros
  • New
Cons
  • I don't remember

Revainrating 1 out of 5

It's good if you make your own wires.

My spark plug wires didn't go through the hole. So I couldn't use it then. I didn't want to disassemble my connector wires. Stock ls cargo wires. Put headings to help. No . ring embedded in the material

Pros
  • A sea of positive emotions
Cons
  • Weight

Revainrating 1 out of 5

Doesn't stretch, breaks really badly

They don't stretch at all I damaged 2 well I have a 6 cylinder so I was fine. At first glance, they appear large and long, but if you try to insert the spark wire, a fight will begin

Pros
  • Absolute legend
Cons
  • Minor issues

Revainrating 2 out of 5

What a PITA: Parts

I installed them on my 2001 Corvette. It was almost impossible to climb over the boots onto the connector wires. I had to pull so hard that the red paint was peeling off my hands. This made the boots look "old" and used. This is the only set I've ever installed, so it's possible they're all PITAs.

Pros
  • Few competitors
Cons
  • Nothing here

Revainrating 1 out of 5

Poor quality item

These cases are not of good quality. As others have said, they don't fit wires well (10mm), although you can open the ring sewn into the material (it's cut) and then insert without cutting the fabric. One of the biggest issues is aesthetics. Even though you can wear them over boots, the color (mine "was" red) is now entirely off the product and on your hands. The one I was able to partially save had the color disappear after 1 week of walking maybe once a day. Don't buy this. Now I'm looking…

Pros
  • Nice packaging
Cons
  • No