🌟 2021 Upgraded LASFIT 1156 BA15S P21W 7506 LED Turn Signal Light - No Hyper Flash & Intelligent Temperature Control - Amber Yellow (Pack of 2) Review

The bulb is significantly brighter during the day. When I went to the car and unlocked the car, the halogen lights were not visible. LED lamps are visible! That's important to me because the turn signal is lower on the bumper. Note: The Revain installation guide says this bulb is not compatible, but it's still the standard size for my car. The best way to check whether a lightbulb will fit is to pull out the existing one in the car and see for yourself!

I have "LASFIT 1156 BA15S P21W 7506 LED Turn Signal Bulbs with CANBUS Anti Hyper Flash" and they can actually be too bright. They are much brighter than regular bulbs and are very noticeable during the day. In the evening they are almost blind. Otherwise they seem to be good. I had no electrical feedback noise on the radio or electrics. I've attached a photo taken during the day and one at dusk.

This lamp is very bright and I love that it has a built in resistor; There is no need to insert a separate resistor. HOWEVER, after 2 minutes of continuous use (sitting at a long traffic light), the lights start flashing. A quick fix is to clear the signal, let the bulb(s) cool for a few seconds and then it should be back to normal. I hope LASFIT improves the shifting. So I am giving them four stars because they are really bright and have a built in resistor but only last 2 minutes of…

I have been looking for a yellow turn signal LED that does not require resistors and have listed it for my 2017 Hyundai Veloster (#1156). They're quite expensive, but the reviews were pretty good and the brand is quite famous for their quality products, so I rolled the dice. I just installed them and WOW they are BRIGHT and a nice amber color and so far they flash great with no added resistors. You look fantastic! If anything changes I will update this review. I'll also try to remember to…

I really like my 2017 Kia Sportage. There is one design feature that I don't like and have never liked. The rear direction indicators are located in the rear bumper. By placing them at a low viewing angle. LASFIT LED BLUBS, without changing the position of the lighting, provides amazing visibility of the direction indicator. There can be no wrong intention when these LED bulbs are lit. CANBUS Hyper Flicker Prevention technology ensures easy installation and eliminates the need for additional…

This saves a lot of time when changing from halogen to LED as it solves the problem of excessive flickering. They do not require the installation of a load resistor. I originally bought LED bulbs not realizing the need for load resistors. Regular LED bulbs cost about $8 per bulb. They cost about $25 for a lightbulb. However, when you add the cost of a terminator for each lamp of about $3 plus the time and effort to install the terminators, the $14-15 difference per lamp is worth my time and…

These bulbs work great, I had to use resistors in another car and the fact that they have built in resistors is handy. I sat next to the flashlight for about 10 minutes with the signal on and the light started flashing, after it cooled it worked fine again. Revain lists them as not compatible with my vehicle even though they have the same socket and function as my OEM light. Another thing, measure your case bore with an engineering ruler (marked 1/32 inch) to make sure these bulbs will work…

I have a 1983 Mercedes Benz W123 300D Turbo Diesel. I had no trouble converting the brake, tail and taillights to LED. Where I've run into a problem is with hyper-flash turn signal bulbs. I must have tried over a dozen different LED bulbs and I was ready to give up! I didn't want to use a pull up resistor because I didn't want to mess with the original wiring and I certainly didn't want to drill holes to fit the car that has been in our family since 1983. Although Revain said these bulbs will…

These things are great. I just wish they had more choices. So I just bought a NEW car and didn't want to make any changes that could later be blamed for a possible future problem, so I didn't want to install resistors on this particular car. .These bulbs are BIG but the seam needs to be just right to go through the sockets for installation. I installed matching bulbs around the perimeter and had no problems with the gap. I had to modify this particular bulb, but without any design or…