Header banner
Revain logoHome Page
๐Ÿ•น๏ธ smakn fr4 ky-023 joystick breakout module sensor shield for arduino uno/arduino uno r3/arduino 2560/arduino 2560 r logo

๐Ÿ•น๏ธ SMAKN FR4 Ky-023 Joystick Breakout Module Sensor Shield for Arduino Uno/Arduino Uno R3/Arduino 2560/Arduino 2560 R Review

3

ยท

Very good

Revainrating 4.5 out of 5  
Rating 
4.3
๐Ÿ–ฅ๏ธ. Single Board Computers, ๐Ÿ’ป Computer Components

View on AmazonView on ะฏM

Media

(4)
img 1 attached to ๐Ÿ•น๏ธ SMAKN FR4 Ky-023 Joystick Breakout Module Sensor Shield for Arduino Uno/Arduino Uno R3/Arduino 2560/Arduino 2560 R
img 2 attached to ๐Ÿ•น๏ธ SMAKN FR4 Ky-023 Joystick Breakout Module Sensor Shield for Arduino Uno/Arduino Uno R3/Arduino 2560/Arduino 2560 R
img 3 attached to ๐Ÿ•น๏ธ SMAKN FR4 Ky-023 Joystick Breakout Module Sensor Shield for Arduino Uno/Arduino Uno R3/Arduino 2560/Arduino 2560 R
img 4 attached to ๐Ÿ•น๏ธ SMAKN FR4 Ky-023 Joystick Breakout Module Sensor Shield for Arduino Uno/Arduino Uno R3/Arduino 2560/Arduino 2560 R

Description of ๐Ÿ•น๏ธ SMAKN FR4 Ky-023 Joystick Breakout Module Sensor Shield for Arduino Uno/Arduino Uno R3/Arduino 2560/Arduino 2560 R

Suitable for Arduino UNO, Arduino UNO R3, Arduino 2560, Arduino 2560 R. Cross rocker is a bidirectional 10K resistor, with rocker in different directions, the resistance changes with tap;. Material:FR4. This module uses 5V power supply, original state of X, Y readout voltage is about 2.5V, when press down the arrow. the voltage value increases up to 5V; press the arrow in the opposite direction, voltage decreases, the minimum is 0V

Reviews

Global ratings 3
  • 5
    1
  • 4
    1
  • 3
    1
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

Smooth Gaming Experience with Joystick Breakout!

This breakout board delivers exactly what it promises - seamless joystick control for my Arduino project. The setup was straightforward and the board fit perfectly on my breadboard. The joystick responsiveness was impressive and added a new level of interactive experience to my project. My only concern was that the documentation could be more extensive for those who are less familiar with wiring and programming. Overall, this product is a great value for anyone looking to enhance their computer

Pros
  • Easy and convenient to use for controlling a joystick on an Arduino project
Cons
  • The joystick breakout only works with certain Arduino models and may require additional wiring for compatibility

Revainrating 3 out of 5

Bad freedom of movement

Basically great. However, the actual range of movement (ie providing a meaningful output signal) for the x and y potentiometers was about the first 30% of travel. The rest of the way was just exhaustion.

Pros
  • Computer and accessories
Cons
  • Annoying

Revainrating 4 out of 5

Works fine but the joystick falls off

I used this equipment to make a forward/backward and left/right joystick for an RC car. Here is the list of required parts: x1: 5 packs 9V battery clip with 2.1mm x 5.5mm DC jack for Arduino by Corpcox1: 2 pcs. 2560/arduino 2560 Rx1: Qunqi 2Packs L298N Motor Drive Controller Board Module Dual H-Bridge DC Stepper Motor for Arduinox1: Multicolor Breadboard, Dupont Jumpers - ALLUS J7011, 120pcs/F), Male to Female (M/F) for Arduino and Raspberry Pix2 : Arduino Uno R3 Breadboard, ATmega328 andโ€ฆ

Pros
  • Computer Components
Cons
  • Expensive