Header banner
Revain logoHome Page
sydien mal series 25mm bore 200mm stroke double acting single rod pneumatic cylinder with y connector and 4pcs pneumatic quick fitting logo

Sydien MAL Series 25Mm Bore 200Mm Stroke Double Acting Single Rod Pneumatic Cylinder With Y Connector And 4Pcs Pneumatic Quick Fitting Review

3

·

Average

Revainrating 3.5 out of 5  
Rating 
3.3
🔩 Pneumatic Equipment, 🚰 Hydraulics, Pneumatics & Plumbing

View on AmazonView on ЯM

Media

(4)
img 1 attached to Sydien MAL Series 25Mm Bore 200Mm Stroke Double Acting Single Rod Pneumatic Cylinder With Y Connector And 4Pcs Pneumatic Quick Fitting
img 2 attached to Sydien MAL Series 25Mm Bore 200Mm Stroke Double Acting Single Rod Pneumatic Cylinder With Y Connector And 4Pcs Pneumatic Quick Fitting
img 3 attached to Sydien MAL Series 25Mm Bore 200Mm Stroke Double Acting Single Rod Pneumatic Cylinder With Y Connector And 4Pcs Pneumatic Quick Fitting
img 4 attached to Sydien MAL Series 25Mm Bore 200Mm Stroke Double Acting Single Rod Pneumatic Cylinder With Y Connector And 4Pcs Pneumatic Quick Fitting

Description of Sydien MAL Series 25Mm Bore 200Mm Stroke Double Acting Single Rod Pneumatic Cylinder With Y Connector And 4Pcs Pneumatic Quick Fitting

Product Name: Mini Pneumatic Cylinder; Size: MAL25 x 200; Package Content: 1 Pcs x Mini Pneumatic Cylinder with 1 Pcs x Y Connector & 4 Pcs x Pneumatic Quick Fitting. Piston rod thread:M10X1.25mm; Port size: G1/8" ;Max.Press: 1MPa; Single Rod double action. Made of aluminum alloy and metal, thickened cylinder body, high quality sealing rod, imported grease. Two screw hole connections to get the air in and out, and a rod connected to the plunger that goes in and out. Cylinder is a mechanical devices which utilize the power of compressed gas to produce a force in a reciprocating linear motion.

Reviews

Global ratings 3
  • 5
    1
  • 4
    0
  • 3
    1
  • 2
    1
  • 1
    0

Type of review

Revainrating 5 out of 5

Suitable for my application

Good for my application. My lowlow goes up and down with no problem. I've pushed 250psi so far, but it's still holding up. had to change a little bit to install it properly

Pros
  • Elegant design
Cons
  • Long delivery time

Revainrating 3 out of 5

a lot of friction

The piston seal has a lot of friction. Once it starts moving it's free, but it takes a little effort to break the o-ring and get it moving. It is difficult to achieve smooth action. The pressure builds up and nothing happens, then it goes on quickly. There will be no problem if higher pressure is applied to the piston (50+ psi is great), but if you're trying to run at low pressure for low forces, friction comes into play. If you want smooth performance at 5-10 psi, this isn't for you. The…

Pros
  • Easy to use
Cons
  • Quick start guide

Revainrating 2 out of 5

Without a job, Rod didn't move at all.

I couldn't move the rod right out of the box. GENERAL. Cylinder disassembled, the rod rotates normally. Finally, it turned out that even with moderate tightening of the top cap, the front part of the cylinder body pressed against the stem, compressing it so much that the stem did not move. He took out the front o-ring and used a round file to remove some material from the edge. Reassembled and now I can move it by hand with the top cap tightened. Tolerances gnaw at it to the point of failure…

Pros
  • Few competitors
Cons
  • unreliable