Upgrade Your Ford F150 2015-2018 / Ford Raptor 2017-2018 With Jaronx No-Drill Pedal Covers - Aluminum Alloy Anti-Slip Gas & Break Pedal Pad Set For Improved Acceleration And Safety Review

Pro:It looks nicer.Larger brake pad than factory.Thick horizontal lines gives better traction.Gas pad cover install was fairly easy.Con:The brake pad install was a hassle. Broke a sweat trying to put the cover on.How I did it: take factory cover off which is just peel one side and pull off. Add generous amount of isopropyl alcohol to slide the rubber on. Wear gloves to pull on the two tabs. First jam that sucker from the top and push down with all your powers and hold. The other hand pull on…

As other reviewers have stated, the accelerator pedal cover goes on fairly easy over the top of the factory pedal cover. The brake pedal cover is more difficult. I did find on their website you have to remove the factory brake pedal cover, but that didn’t help much. There are no instructions anywhere that I could find. I did discover that if you use a pair of pliers to pull on the two tabs as you are putting it on, you can get it on okay. Still not easy, but it helps a lot! Hope this helps…

These look very good once you get them installed. However, the emphasis is on "once you get them installed". Not gonna lie, it's takes some work getting them on. Get you a stubby flathead screwdriver, slide one side on, and start lifting the rubber over the peddle. Sounds easy, but it's not. Takes a lot of effort and a whole lot of patience. Both of these I've got. So if you have patience, like me, you'll feel good afterwards. However if you don't, (like my friend who shall remain nameless)…

Used on 2015 F-150 platinum: amazing tight positive fit! Very hard to install break pedal pad but gas and parking break was flawless and easy to install on gas pedal and break install from underside then push upward after getting edges to fit. High quality product, no slip means no slip, finish is very nice looking and functionally even with dirty or wet boots the products surfaces seem to stay pretty clean and stay new looking. Much easier to clean surfaces vs stock pedals. Gives a more…

All three appear to have rubber molding defects as you can see in the pictures. Possibly tabs to assist with pulling them on but as you can see in the 2nd pic the tab clearly shows/is visible on the gas which doesn't look correct. The E brake slid right on but the defective mold will likely let it slide off. The gas pedal one went on over the existing after a struggle. (Stock wont come off) Removed the brake rubber pedal and this is where my biggest complaint comes from. The one I received for…

I’m glad I purchase these and I like looking at them every day as I get in. Not many people notice them but when they do I like that they see an aftermarket touch that most vehicles don’t have. However, I wish I would’ve known that when installing these one of the pedals would be one of the most difficult things to do that I could have imagined. If you don’t have extremely strong hands you will never get one of these mounted over the pedal. It basically just slides over and wraps around the…

Very hard to stretch over the foot pedals. Look very nice bug after a while o just stopped trying to get them on That's my review.

Got the gas pedal on in about 45 seconds. Used a hair dryer to soften the rubber and a bit of dish soap to slip the pedal on easier. Easy Peasy. Now, the brake pad.OMG! What a waste of time and money. Did the same thing as with the gas pedal cover. Heated with hair dryer. Added dish soap. 45 mins later.it will NOT go on. Emailed the seller. They forwarded a install video that would not load. Then, they told me to use a body panel tool to help pull the lips away from the pedal so they would slip

These look nice but theres absolutely no way in hell to get the brake pedal to fit, the rubber simply is too small and theres this big bevel in the center for absolutely no reason other than to make it not fit. The gas pedal went on fine though.

These look great in my Raptor. the install was pretty easy. I used a little windex to make fitting them a bit easier That's my review!

These pedal covers look great. Two reasons I'm giving them 4 stars rather than 5:1. The break pedal cover is VERY hard to install.2. The bags they come in, came opened.For installation, notice the orientation from my photo for your reference.Unlike the break pedal, the gas pedal cover just goes over the current pedal as is. It's easy to install.The break pedal does have a cover that you need to remove before installing the new one. It is hard to install. Try starting from the opposite corner…

Very nice product, because of the way the pedals are configured.Definitely not for a 2014 f150. I was able to use the the small energy brake portion. So I bought the right ones that fit. Now I am very satisfied please with the end results. Looks fabulous.

Only hiccup was realizing the current brake cover has to be removed while the gas pedal goes over the waiting pedal. Once I figured that out it was quick and easy to install.

I would rate it five stars if it actually fit what it was supposed to. but I got a razor blade made some modifications and now it's perfect.

Love the look, but was really hard to install the break cover, cut my hand with plier trying to hold it.back rubber part broke and and threw it away.kept the gas pedal cover on still looks go.thanks

The ebrake and accelerator pedals are a breeze to install. 5 min install at max. The brake pedal however a different story. Like most have stated it’s very difficult. What worked for me was to adjust pedals to their most upward position so you have room behind the pedal. Working from left to right (from ebrake to accelerator) and down to up. I then used a pair of pliers and grabbed the rubber flap at the right and the pedal to aide in getting it on. I did the same for the top of the pedal. Went

Not easy to install on 2016 f150. Gas and park break went pretty easy with a little effort. The brake pedal took 4x longer, had to remove metal plate from rubber and I had to use some tools to help stretch and push the flap edges over edge of pedal base. Took some effort to put metal plate back over rubber. Gives a good look though and seems better grip on shoe over factory pedal cover.

Difficult to install. Hotter the day the easier the application. I did mine during the winter and had to use a grill lighter and soap to get the edges on the brake pedal. Acceleration and parking brake pedals were easy.