Upgrade Your Power Washer With A Vertical Pressure Washer Pump Replacement - 2400-2800PSI, 7/8'' Shaft Review

I like the extra PSI, 2800, versus only 2000 from my original pump for tough jobs like cleaning my cement driveway surface, deck surface and house siding. Like someone else said in reviews, the pump could be a bit much for my small 3.75 HP motor, but I remember torturing Briggs and Stratton on go-karts when I was a kid and these classic Briggs and Stratton Sprint motors can take it. I will re-post here if the motor blows up, which I seriously doubt it will as long as I change the oil…

My boss gave me his old gasoline power sprayer; told me the engine worked but the sprayer was not good. Bought this replacement pump and it works like brand new!

I thought I was buying an exact replacement for the old pump. This pump, however, had thicker base castings than the original. Also I had to drill out one hole which had casting flaws in it. All in all it was a good pump but people need to know they may have to acquire longer bolts to mount it properly.

Works very well on my troy-bilt pressure washer, cheapest option available as well. We'll see how long it lasts, but even it's only 2-3 years, still worth the purchase.

Repaired a Husky HU80522 with this pump. Added 3/8” elbows and pipes from the old pump. Water in connection at the front and water out at the back. Output side leaks a little but the pump itself works well. Maybe needs more Teflon tape. Tilted both pipes so they drain after use. I had to raise the pump by changing the bolts that hold the feet as the pump is a little taller. Shaft and bolts fit well. Pretty happy to have the washer up and running again.

The first pump installed easily but when used appeared to lug the engine more than the original system. Should have realized there was a problem as this pump failed during use on the second tank of fuel - simply lost power. When pulled, I discovered that the pump shaft had split at the keyway and allowed the key to pull out of keyway thus engine was spinning in the pump shaft. The company (or Walmart) replaced the pump without question. The second pump was more difficult to install due to…

Troy Bilt power washer ? If you want to use this pump then you will need longer screws and shims that are not included or any instructions to do it.It is a challenge for even a skilled mechanic. False claim to to be a replacement part.If you are going to buy this anyway, then purchase some mounting bolts that are 1" longer and some bushings that are about 1/4 inch tall.

It did not fit my craftsman power washer. Will have to return it. Disappointed. Wish I could talk to the manufacturer to see if they have another one that fits. But we received it promptly.

Seems to be a rugged replacement for my OEM pump. I have used in only a handful of times since installation and so far no failures, e.g. leaks or poor performance. I would recommend it.

Hole alignment for my craftsman power washer required 180 deg rotation from original mounting. Small in convenience. Easy mounting. Works great.

new pump bolted up to my troy built pressure washer with 158cc Briggs/Stratton engine perfectly - just had to add 6, 3/8" flat washers as shims between pump and chassis, not a big deal. Original bolts worked fine, Works great now !

It fit the honda power washer , only thing i had to do was take bottom section off and rotate 90 degrees to i could get the water to hook up because it was in the way of the axle on the power washer.

It fit on a Power Stroke 2200 with the 7/8 shaft and works like a dream! Easy installation and 1/3 the price of an Original!

While I've only had it installed for a day so far, this fixed my issue and was a direct replacement for the pump on my Black Max BM80919 Pressure Washer. Not sure of the exact pressure it's outputting but it seems as strong as the factory pump before it died. Time will tell if the cheaper pump will last as long as the factory pump.

I compared the photo of this pump to the original pump and they looked almost identical. I ordered and had the replacement pump in two days. I unbolted the failed pump, lined up the key in the motor shaft, and the new pump slipped into place. Less than 30 minutes and I was up and running again.My only concern during the installation process was the length of the original bolts becasue the attachment points on the new pump were about 1/8 thicker than on the original pump. This turned out to not…

liked speed of product arrival was only 2 days from order time. price was good value compared to manufacture price was twice as much and no longer offered for cambell hausfeld pw2200v3le model. needed to drill mounting holes larger in pump base and add 3 washers per leg to clear frame but overall would give 4 1/2 stars

Was unable to use. This pumps connections are on rear of machine, I needed front connections. Picture was deceiving. Thanks for attention.

Pump working great, but the legs are to thick for the Craftsman unit. It took a extra 30 minutes to fit the legs. Everything else fit good

My pressure washer had a great running 6 h.p. Briggs and Stratton engine. I needed some longer 5/16 bolts, It was worth the cost and effort. Better than new old pump was 2300 p.s.i.

Specifically contacted seller before purchase to confirm pump would work for my pressure washer. Provided both the pressure washer model number and existing pump model number. Seller indicated pump would be the right part. Seller’s pump does not accommodate the idle down feature of my pressure washer. If you have the idle down feature, don’t buy this pump. I was hesitant to buy a cheap aftermarket part instead of OEM - and I should have trusted my instinct.