Header banner
Revain logoHome Page
tubeless tire valve stems for bonneville daytona 600 monster 821 - front and rear logo

Tubeless Tire Valve Stems for Bonneville Daytona 600 Monster 821 - Front and Rear Review

5

·

Terrible

Revainrating 1.5 out of 5  
Rating 
1.4
🔧 Tires & Wheels Parts, 🚘 Tires & Wheels

View on AmazonView on ЯM

Media

(4)
img 1 attached to Tubeless Tire Valve Stems for Bonneville Daytona 600 Monster 821 - Front and Rear
img 2 attached to Tubeless Tire Valve Stems for Bonneville Daytona 600 Monster 821 - Front and Rear
img 3 attached to Tubeless Tire Valve Stems for Bonneville Daytona 600 Monster 821 - Front and Rear
img 4 attached to Tubeless Tire Valve Stems for Bonneville Daytona 600 Monster 821 - Front and Rear

Details

ColorBLACK
Material铝
BrandXitomer
Fit Type万能装配
Vehicle Service TypeMotorbike

Description of Tubeless Tire Valve Stems for Bonneville Daytona 600 Monster 821 - Front and Rear

Fitment for More Motorcycles in Product Description. CNC Made from High Quality 6063-T6 Aluminum with Top Quality Rubber Seals to Effectively Avoid Air Leaking. 90 Degree Tubeless Snap-in Valves for Inflation and Checking Air Pressure. The Right Angle Bend allows Easy Access for the Pump or Airline. They Change the Angle 90° to Fill-up the Tires. ( the Original Tire Valves is Vertical, and Xitomer One is Horizontal to the Ground. ).

Reviews

Global ratings 5
  • 5
    0
  • 4
    0
  • 3
    1
  • 2
    0
  • 1
    4

Type of review

Revainrating 3 out of 5

OK Chinese Fake

Your main Chinese counterfeit. The original Italian version is definitely better. However, this product will likely work just fine.

Pros
  • CNC Made of high quality 6063-T6 aluminum with high quality rubber seals to effectively prevent air leakage.
Cons
  • Miscellaneous Miscellaneous

Revainrating 1 out of 5

BOTH CORE BAD

Installed on my bike and both cores were not holding air. Luckily I had spares, but BOTH still couldn't hold their breath.

Pros
  • Right angle bend allows easy access to pump or air line.
Cons
  • Faulty

Revainrating 1 out of 5

Looks good but doesn't work on all drives.

I liked the look of them and the small valve fit my front wheel (Suzuki GS1000 1980) but so did the stem on the valve short to affect my rim.

Pros
  • You change the angle by 90° to inflate the tires. (Original tire valves are vertical while the Xitomer One is horizontal to the ground.)
Cons
  • Some bugs

Revainrating 1 out of 5

Most likely they are made for a bike. I hope they take her back.

I was going to put these on a 1982 Suzuki gs1100 but the rubber shoulder doesn't fit in the hole. Even if I drilled it, it would be like this. it may still be too short to fit through the rim.

Pros
  • Tubeless 90 degree snap valves for inflating and checking air pressure.
Cons
  • silent

Revainrating 1 out of 5

Not suitable for Aprilia (Tuono) wheels

The included O-ring, if you want to call it that, increases the diameter so the valve stem bore in the wheel should be closer to 11mm. This means it will not fit Aprilia 8.3mm wheels. The design seems good, but they don't fit 8.3mm wheels.

Pros
  • Suitable for other motorcycles in the product description.
Cons
  • Blank