Header banner
Revain logoHome Page
๐Ÿ›ก๏ธ jdmspeed black shield protective sleeve logo

๐Ÿ›ก๏ธ JDMSPEED Black Shield Protective Sleeve Review

7

ยท

Average

Revainrating 3 out of 5ย ย 
Ratingย 
3.1
๐Ÿงฏ Ignition Parts, ๐Ÿ› ๏ธ Replacement Parts

View on AmazonView on ะฏM

Media

(4)
img 1 attached to ๐Ÿ›ก๏ธ JDMSPEED Black Shield Protective Sleeve
img 2 attached to ๐Ÿ›ก๏ธ JDMSPEED Black Shield Protective Sleeve
img 3 attached to ๐Ÿ›ก๏ธ JDMSPEED Black Shield Protective Sleeve
img 4 attached to ๐Ÿ›ก๏ธ JDMSPEED Black Shield Protective Sleeve

Description of ๐Ÿ›ก๏ธ JDMSPEED Black Shield Protective Sleeve

6 inches long Spark Plug Heat Protector both for boot and wire(Pack of 8). LEDAUT Spark Plug Boot Cover is Made from fiberglass material,protect from Heat from 1000 Fahrenheit (550 Celsius). Note: only fit for vehicles which burning petrol. Manufacture Part Number: SBC BBC 350 454. Compatible:1) For most straight or angled boots.2) For most hot rods and classics engines, such as 265 283 305 307 327 350 383 400 396 402 427 454 472 502 260 289 302 351W 347 352 360 390 406 427 428 429 460 351C 351M 400M 273 318 340 360 361 383 400 413 426W 440 455 330 326 engines.

Reviews

Global ratings 7
  • 5
    2
  • 4
    2
  • 3
    0
  • 2
    1
  • 1
    2

Type of review

Revainrating 1 out of 5

Not for Lasso Ford F1501998.

It was not possible to incorporate this into the cables. They look like they are of really good quality. but what doesn't fit you can't star high.

Pros
  • Stylish and modern design
Cons
  • Cable is shorter than other picks

Revainrating 5 out of 5

good protection. for coil covers

After spending a lot of money on a complete overhaul of my truck I wanted to go a step further and try to protect the spark plug leads from the heat of the exhaust manifold. as well as from road debris and inclement weather. They fit well and are well made.

Pros
  • Few competitors
Cons
  • No instructions

Revainrating 4 out of 5

The only problem I had with this product was.

The only issue I had with this product was the metal clip used on one end to secure the cuff to the connector wire. The metal clip was such a small circumference that it was impossible to put a shoe on the end of the connector wire so you had to spread the clip further and if you are not careful you can spread it too far and it won't fit properly on the plug. insert angle piece.

Pros
  • High marks for support and durability from testers
Cons
  • Clarity

Revainrating 5 out of 5

Works great in Coil On Plug Boots

These boots are a perfect fit. Best used with factory steel 8006 insulator. Some say they won't fit. It is not true. All you have to do is remove the rubber boot from the coil side and slide the insulator over the factory steel insulator toward the large side of the spark plug. Reinstall the rubber boot on the coil side by applying a small amount of dielectric grease to the coil wire and connector. Use a wire tie to protect the wire and sleeve from direct contact with manifolds, turbines, orโ€ฆ

Pros
  • Weight
Cons
  • Not for everyone

Revainrating 2 out of 5

Wire had to be cut to fit over spark plug boot

Used on Chevy Silverado with Kooks terminals and special red spark plug wires. It's impossible to put them on spark plug ends and metal guards without cutting the round wires. It wasn't easy to cut the wires, which caused part of the sleeve to unravel a bit, but this isn't visible. Looks well installed and still seems to be holding up and working as intended. Updated August 20: Pretty useless. Some turned white from the heat, I doubt they did anything.

Pros
  • Certified
Cons
  • Upgradeable

Revainrating 4 out of 5

Despite some fit issues, I'm glad I have them.

These grommets are not part of a cable set so they will not slip off the Taylor cables I was planning to install at the same time. The sleeves have a 5/8 inch ring on one end that is sewn into the fabric and will not ride over the new wires I bought. Corvettes are notoriously "heat soaked" in the wiring, so I'm glad I got hold of them and installed them despite the installation issue.

Pros
  • Works great for me
Cons
  • Reliability

Revainrating 1 out of 5

Don't waste money and time.

Don't waste your time and money when using headlines. After installing the headers on the first start, I noticed some smoke coming from the engine bay of my 63 Nova. I thought it was just some kind of grease that got on the headers during installation. After about 5 minutes the smoke intensified so I went to see where it was coming from. I immediately noticed that it comes from 4 of these sleeves. All bushings that touched the collector tube were burned out after 5 minutes! I could only imagine

Pros
  • Impressive
Cons
  • Boring Packaging