Header banner
Revain logoHome Page
πŸ”§ plaxcon ag60 sg55 plasma standoff guide two point standoff compatible with cut50 cut50d cut50dp cut60 lgk60 plasma cutter ag60 / sg55 plasma cutting torch accessories pk-2 logo

πŸ”§ PLAXCON AG60 SG55 Plasma Standoff Guide Two Point StandOff compatible with CUT50 CUT50D Cut50DP Cut60 LGK60 Plasma Cutter AG60 / SG55 Plasma Cutting Torch Accessories PK-2 Review

5

Β·

Average

Revainrating 3.5 out of 5Β Β 
RatingΒ 
3.4
πŸ”¨ Welding Tools, πŸ”§ Automotive Tools & Equipment

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ”§ PLAXCON AG60 SG55 Plasma Standoff Guide Two Point StandOff compatible with CUT50 CUT50D Cut50DP Cut60 LGK60 Plasma Cutter AG60 / SG55 Plasma Cutting Torch Accessories PK-2
img 2 attached to πŸ”§ PLAXCON AG60 SG55 Plasma Standoff Guide Two Point StandOff compatible with CUT50 CUT50D Cut50DP Cut60 LGK60 Plasma Cutter AG60 / SG55 Plasma Cutting Torch Accessories PK-2
img 3 attached to πŸ”§ PLAXCON AG60 SG55 Plasma Standoff Guide Two Point StandOff compatible with CUT50 CUT50D Cut50DP Cut60 LGK60 Plasma Cutter AG60 / SG55 Plasma Cutting Torch Accessories PK-2
img 4 attached to πŸ”§ PLAXCON AG60 SG55 Plasma Standoff Guide Two Point StandOff compatible with CUT50 CUT50D Cut50DP Cut60 LGK60 Plasma Cutter AG60 / SG55 Plasma Cutting Torch Accessories PK-2

Description of πŸ”§ PLAXCON AG60 SG55 Plasma Standoff Guide Two Point StandOff compatible with CUT50 CUT50D Cut50DP Cut60 LGK60 Plasma Cutter AG60 / SG55 Plasma Cutting Torch Accessories PK-2

Plasma Consumables Type: Plasma Standoff Guide AG60 / AG-60 / SG55 / SG-55 plasma cutting torch consumables. Two Point Standoff Guide can fit AG60 / AG-60 / SG55 / SG-55 plasma cutting torch with Slotted shield cap. The AG60 SG55 Plasma stndoff guide can fit AG-60 / SG-55 torch work with Cut50 & CUT50D & Cut50DP & CT520D & CT520DP & CUT50P plasma cutter torch. The AG60 SG55 Plasma stndoff guide can fit AG-60 / SG-55 torch work with CUT60, LGK60, 50DX, 50RX 520D plasma cutter torch. High quality PLAXCON brand replacement AG60 / AG-60 / SG55 / SG-55 plasma cutting consumables, not original.

Reviews

Global ratings 5
  • 5
    2
  • 4
    0
  • 3
    1
  • 2
    2
  • 1
    0

Type of review

Revainrating 5 out of 5

Does not fit all plasma cutting attachments

After closing the loop a bit, it gets to the end of my plasma cutter, falls off, but that's no problem. The thing is, it leaves a gap so it's easy to trim, and it does.

Pros
  • Welding and Soldering
Cons
  • Useless Functions

Revainrating 2 out of 5

Works better than factory

Works much better than the cheap wire my plasma torch came with. They're a little tricky to put on and 1/16th shorter than I'd like, but they work and last longer than the wired ones.

Pros
  • Welding Equipment and Supplies
Cons
  • Volume

Revainrating 3 out of 5

Like most foreign products, barely enough

Doesn't fit fully but stops at the serrated part of the cup. Not solid so it moves a little. It stays in place as you pull, as long as you don't put too much pressure on it to make the lead slip off completely (where it should be anyway). All in all just another cheap junk from abroad.

Pros
  • Tools and Housewares
Cons
  • Expensive

Revainrating 5 out of 5

Would give 10 stars if I could!

I don't usually write reviews but I'm so pleased with these little cages I just had to turn on my computer. I love my Primeweld Cut50DP and this bug has been fixed. The only thing I didn't like about it was the crappy wire mesh it came with. This little rascal makes precise cuts a lot easier. Love it!

Pros
  • Welders
Cons
  • New Competitors Arrive

Revainrating 2 out of 5

Incorrect listing

This is not a Plaxcon part as listed. This is a Weldingstop part available elsewhere for $1 each. This is not a typo. This is their cheapest low-end rack, not the high-performance rack that sells for around $5. As others have said, this fits the AG60 loosely. Nowhere on the Weldingstop or Plaxcon website does it state that it is stainless steel. Although it appears to be stronger than other similar Chinese alloy parts, it seems to me that it is too light for stainless steel but too heavy for…

Pros
  • Welding Equipment and Supplies
Cons
  • Large and Bulky