Header banner
Revain logoHome Page
efficient oil rail leak repair kit for 2003-2007 ford 6.0l powerstroke - pack of 8 o-rings + injector seal kits logo

Efficient Oil Rail Leak Repair Kit for 2003-2007 Ford 6.0L Powerstroke - Pack of 8 O-rings + Injector Seal Kits Review

5

·

Terrible

Revainrating 1 out of 5  
Rating 
1.0
🛢️ Fuel System, 🏎️ Performance Car Parts & Accessories

View on AmazonView on ЯM

Media

(4)
img 1 attached to Efficient Oil Rail Leak Repair Kit for 2003-2007 Ford 6.0L Powerstroke - Pack of 8 O-rings + Injector Seal Kits
img 2 attached to Efficient Oil Rail Leak Repair Kit for 2003-2007 Ford 6.0L Powerstroke - Pack of 8 O-rings + Injector Seal Kits
img 3 attached to Efficient Oil Rail Leak Repair Kit for 2003-2007 Ford 6.0L Powerstroke - Pack of 8 O-rings + Injector Seal Kits
img 4 attached to Efficient Oil Rail Leak Repair Kit for 2003-2007 Ford 6.0L Powerstroke - Pack of 8 O-rings + Injector Seal Kits

Description of Efficient Oil Rail Leak Repair Kit for 2003-2007 Ford 6.0L Powerstroke - Pack of 8 O-rings + Injector Seal Kits

Over The Time The Seals Commonly Leak Causing Hart Start ,Or Not Start Conditions.Replacing The Ball Valves And Seals Saves Money And Time By Eliminating The Need To Replace The Entire The Oil Rail. Injector Seal Repair Kit is manufactured from high-quality materials for durability,Direct replacement for a proper fit.This Product are Tested and Meet Or Exceed OEM Performance Requirements. High Pressure Ball Tubes connects the fuel injector to the high pressure oil rail. All of our High Pressure Ball Tubes include gaskets for a complete repair. FOR Ford 6.0L Powerstroke 2003-2007. Important Note: This is a professional tool, there is no instruction manual, please find a professional person to operate and install. Package include: 1x Removal Tool, 8x Ball Tubes, 8x O'Ring Seals, 8x Steel Snap Rings, 8x Injector D-Rings, 8x Upper Injector O-Rings, 8x Lower Injector O-Rings, 8x Copper Crush Washers, 8x Outer Injector Harness O-Rings, 8x Inner Injector Harness O-Rings(As Picture).

Reviews

Global ratings 5
  • 5
    0
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    5

Type of review

Revainrating 1 out of 5

Do Not Buy: Injectors & Parts

I want to return this item. Complete garbage. Nipples are rough machined to allow movement during installation. Irving failed the air test after installation. Not even a crank.

Pros
  • Automotive
Cons
  • No Job

Revainrating 1 out of 5

These CHARACTER O-Rings fit Gasket Kits

DO NOT BUY! This whole kit is junk and you will be very sad if the seals fail with just factory air. All that work and what did you save? I have to do it all over again myself. These nozzle seals performed well at 10 psi. Unfortunately, it takes over 600psi or better and up to 3,000 workers to run.

Pros
  • Fuel Injection
Cons
  • I really don't like this everything is fine

Revainrating 1 out of 5

DON'T SPEND MONEY

I noticed that the centers of the two nipple cups were not fully machined. I installed what I needed to get my truck running. I lubed them and the gaskets and put them back in place, but once I tightened the other cups in the guide they didn't move at all. I even dropped 10 pounds of torque and tried to move them but they still wouldn't move. Also, the white injector o-rings were the wrong size and fell off when held upright. That is trash!

Pros
  • Injectors and parts
Cons
  • Waiting too long

Revainrating 1 out of 5

Absolute rubbish! fits fuel system

Nipple cups are absolute junk, sharp edges full of metal shavings and burrs. It will take hours to clean them! Top nozzle seals are questionable in that they work, they are very soft and seem too thin in the middle to seal properly. Would send it back but I need a truck so I used o-rings and a tool. UPDATE: The o-rings between the top of the injector and the nipple cup failed immediately as stated, they appeared to be flimsy and apparently they are! Absolute waste of money!

Pros
  • Gasket Kits
Cons
  • Style 90

Revainrating 1 out of 5

I am a fool! for injectors and parts

I was skeptical about the o-rings in this set, cross section too small, overall diameter too large. If only I had nothing to do but take this motor apart, reassemble it with this crap and test it for 5 miles just to take it apart again. This place shouldn't even advertise the product they sell. Birds on all metal parts, nothing on this place has been quality checked, if they check then someone should be fired. Like a CEO who hired inappropriate hunches on this earth. health for you. OEM OR…

Pros
  • Spare parts
Cons
  • Some small things