Header banner
Revain logoHome Page
πŸ”„ autex stainless pressure transducer - ideal for compatibility logo

πŸ”„ AUTEX Stainless Pressure Transducer - Ideal for Compatibility Review

3

Β·

Average

Revainrating 3.5 out of 5Β Β 
RatingΒ 
3.7
πŸŒ€ Pressure & Vacuum, πŸ” Test, Measure & Inspect

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ”„ AUTEX Stainless Pressure Transducer - Ideal for Compatibility
img 2 attached to πŸ”„ AUTEX Stainless Pressure Transducer - Ideal for Compatibility
img 3 attached to πŸ”„ AUTEX Stainless Pressure Transducer - Ideal for Compatibility
img 4 attached to πŸ”„ AUTEX Stainless Pressure Transducer - Ideal for Compatibility

Description of πŸ”„ AUTEX Stainless Pressure Transducer - Ideal for Compatibility

100% brand new Pressure transducer/sender/sensor 150 psi stainless steel for oil,fuel,air,water; 150 psi Pressure transducer/sender/sensor/Transmitter for oil/fuel/air/water; 150 psi oil/fuel/air/water Pressure transducer/sender/sensor/Transmitter, Our material is using top of line 316 stainless steel and high temperature auto-graded plastic. Output: 0.5V–4.5V linear voltage output. 0 psi outputs 0.5V, 100 psi outputs 2.5V, 150 psi outputs 4.5V. Pressure Medium:The gas and liquid which is compatible with 316L stainless steel / Electromagnetism Compatibility:EN50081-1; EN50082-2; IEC61000-4-3. Interchange Part Number: 5VDC. Package include: 1 pcs x150 psi pressure transducer.

Reviews

Global ratings 3
  • 5
    0
  • 4
    2
  • 3
    1
  • 2
    0
  • 1
    0

Type of review

Revainrating 4 out of 5

Pinout information ERROR in the product description!

I would give 5 stars but the fact that whoever wrote the product description for it gave incorrect pinout information deserves at least one star. I have included photos of what is actually listed on the sensor itself. Correct pinout (for sensors that were shipped to me): red wire = VDD (+5V), black wire = ground, green wire = output (0.5v for 0psi to 4.5v for 150 pounds per square inch) .

Pros
  • Test, Measure & Inspect
Cons
  • Excessive price

Revainrating 4 out of 5

Fuel Pressure Sensor - 150 PSI

This sensor will work as long as you calibrate it properly. (150psi = 4.5V). I'm using this in an Aeromotive FPR to measure fuel pressure on my 2005 STI (using a TGV wiring harness to tie data to the Cobb access port). The calibration is slightly different I would say +/- 1.5psi compared to the liquid sensor I had. previously connected. Otherwise it has been working on the e85 for 2 months without any problems. I've had several other cheap sensors that died after a few weeks of use, but so far…

Pros
  • Pressure Probes and Sensors
Cons
  • Some Little Things

Revainrating 3 out of 5

Good quality sensor. The braid broke off immediately.

This is a very good quality sensor. The problem I had was the clip on the pigtail broke IMMEDIATELY. The pigtail itself is large, bulky, and made of low-quality plastic. I took it out of the box, connected the two together and the clip broke as they connected. Luckily they have a very tight fit and the silicone seal gives little friction. I hope it stays connected for my application. It would be nice if I could find a replacement for the pigtail, although it doesn't look like the standard…

Pros
  • Pressure and Vacuum Sensor
Cons
  • Expensive