Header banner
Revain logoHome Page
๐Ÿ”ง bczamd printer upgrade plastic accessories: enhanced for better performance logo

๐Ÿ”ง BCZAMD Printer Upgrade Plastic Accessories: Enhanced for Better Performance Review

3

ยท

Average

Revainrating 3.5 out of 5ย ย 
Ratingย 
3.3
๐Ÿ”ง Linear Motion Products, ๐Ÿ”ฉ Power Transmission Products

View on AmazonView on ะฏM

Media

(4)
img 1 attached to ๐Ÿ”ง BCZAMD Printer Upgrade Plastic Accessories: Enhanced for Better Performance
img 2 attached to ๐Ÿ”ง BCZAMD Printer Upgrade Plastic Accessories: Enhanced for Better Performance
img 3 attached to ๐Ÿ”ง BCZAMD Printer Upgrade Plastic Accessories: Enhanced for Better Performance
img 4 attached to ๐Ÿ”ง BCZAMD Printer Upgrade Plastic Accessories: Enhanced for Better Performance

Description of ๐Ÿ”ง BCZAMD Printer Upgrade Plastic Accessories: Enhanced for Better Performance

Upgrade Rod for your printer or DIY your own printer. The Teflon coating will increase a little bit thickness. If the bearing installation will not get stuck, you need to use sandpaper to sand off the Teflon coating at the position where the bearing is connected, so that the bearing can be installed. Rod/ Lead Screw Main Material: Made of Stainless steel, surface is covered by the PTFE/ Teflon which Generally called "non-stick coating" or "easy clean wok material", it is a synthetic polymer material that uses fluorine to replace all hydrogen atoms in polyethylene. Comes with POM Nut, Material: POM, it is a special Engineering plastic material, common name is"Saigang" which closed to the properties of steel, light weight, wear resistance, corrosion resistance, insulation, non-magnetic, quiet, high strength, tensile strength and compression resistance. Lead Screw Total Length: 300mm/ 11.8 inch, Lead Screw Diameter : 8mm/ 0.3 inch, Pitch 2mm/ 0.07 inch;. Compare with only Stainless steel lead screw, Advantage: Chemical Resistant, Water and Heat Resistant, Wear resistance, Non-Stick Surface, High lubrication.

Reviews

Global ratings 3
  • 5
    1
  • 4
    0
  • 3
    1
  • 2
    1
  • 1
    0

Type of review

Revainrating 3 out of 5

There are problems with the attachment

As far as I know the description says that it is a teflon coating. However, I have an anti-play nut made from POM. Finding these anti-backlash nuts very handy, I combined the teflon coated threaded rod and the POM nuts and to my surprise encountered a seizure as the Z-axis didn't move at all, the stepper motor couldn't overcome the mechanical resistance. Maybe they are not intended to be used in this combination? Also, the rod doesn't easily fit into the rod sleeve, but this was stated in theโ€ฆ

Pros
  • Very good price
Cons
  • piggy bank price

Revainrating 5 out of 5

Can't say anything bad about this product. That works great.

I have two Ender 3. Pro and V2.k This makes the Z axis heavy. So I switched to dual Z axis on both printers. After switching to a dual Z-axis, I had trouble keeping the Z-axis level, and even after applying Teflon grease to the screws, I heard a creaking sound from time to time, and the Z-axis eventually became uneven. I bought 4 of these screws and upgraded both printers. There is no more squeaking and the levels are stable. Mission accomplished. I'm not sure I can explain it just by addingโ€ฆ

Pros
  • High marks for support and durability from testers
Cons
  • Not as thick as other options

Revainrating 2 out of 5

DO NOT BUY! 3 out of 3 damaged/defective. Bare metal on both ends of each lead screw!

I was so happy to get them. I bought 2. Both rods are connected at each end. Replaced 1 and the one sent was worse than. The one that needs to be replaced! Upon further investigation, I found that there were spots on each end of each lead screw that were not teflon coated or defective. Not sure why all three different leadscrews have it, but all three leadscrews had issues. In the photos below you can see what I'm talking about. As the light reflects, there are clear spots where bare metal isโ€ฆ

Pros
  • Nice to use
Cons
  • old