Header banner
Revain logoHome Page
πŸ”³ honjie 12mm round steel leather craft hollow hole punch for leather belt watch bands and gaskets - 1pc logo

πŸ”³ HONJIE 12mm Round Steel Leather Craft Hollow Hole Punch for Leather Belt Watch Bands and Gaskets - 1PC Review

5

Β·

Poor

Revainrating 2.5 out of 5Β Β 
RatingΒ 
2.5
πŸ‘ž Leathercraft, 🧢 Crafting

View on AmazonView on Π―M

Media

(3)
img 1 attached to πŸ”³ HONJIE 12mm Round Steel Leather Craft Hollow Hole Punch for Leather Belt Watch Bands and Gaskets - 1PC
img 2 attached to πŸ”³ HONJIE 12mm Round Steel Leather Craft Hollow Hole Punch for Leather Belt Watch Bands and Gaskets - 1PC
img 3 attached to πŸ”³ HONJIE 12mm Round Steel Leather Craft Hollow Hole Punch for Leather Belt Watch Bands and Gaskets - 1PC

Details

MaterialAlloy Steel
BrandHONJIE
Item Dimensions LxWxH3.94 x 0.63 x 0.63 inches

Description of πŸ”³ HONJIE 12mm Round Steel Leather Craft Hollow Hole Punch for Leather Belt Watch Bands and Gaskets - 1PC

Punch Diameter:12mm/0.47"; Total length: Approx. 10cm/3.94". Easy to use by placing gasket hole punch over area with a hammer or mallet. Made of high quality steel material, sturdy and sharp edge, can long time used. The special design can save energy and easily cut through multiple layers of fabric. Used for handcraft of belt, gaskets, leather, canvas, paper, plastic, vinyl and rubber ,etc.

Reviews

Global ratings 5
  • 5
    1
  • 4
    0
  • 3
    2
  • 2
    0
  • 1
    2

Type of review

Revainrating 1 out of 5

Soccer EURO approved

You need a tool to cut holes for the speed flexor chamber, this is your salvation, perfect circle cut, perfect size

Pros
  • There's something to it
Cons
  • Not trendy

Revainrating 5 out of 5

Makes beautiful plastic discs

Some people want holes in the leather, I want discs. Get good discs. 15mm cartridges will fit 20 gauge cartridges as washers rather than gas seals. I have cut hundreds of plastic discs from plastic #4, LDPE. I'm sure it will cut the skin.

Pros
  • Hole Punch Diameter: 12mm/0.47in; Total Length: Approx. 10cm/3.94inch.
Cons
  • Not sure

Revainrating 1 out of 5

Completely useless die cutting and stamping tool

A large dent has appeared on the cutting edge. I sharpened and sharpened it to an acceptable level (it was dull as a rock when it emerged). He cut two circles out of about 7 ounces of leather before getting too bored to do more than just emboss a circle on the remaining cuts. I reworked it and tried again. He carved a circle and was too boring for another. I threw it away afterwards. Don't waste your money on this garbage.

Pros
  • Used to make belts, gaskets, leather, canvas, paper, plastic, vinyl, rubber, etc.
Cons
  • No machine gun

Revainrating 3 out of 5

Not very keen on leathercraft

I had read the reviews beforehand and knew the sharpness and hardness would be a problem with this hammer. However, I really needed a 20mm punch, so I went ahead and bought one. I used a hole punch to make 50-60 holes in 6 layers of 1/8" thick foam glued together (don't ask). In any case, foam is a lot softer than leather, and I still had to make about every 10 Stop punching and use my multi tool to sharpen this punch, it didn't make clean cuts and I don't plan on repeating the process if I…

Pros
  • Special design saves energy and easily cuts through multiple layers of fabric.
Cons
  • So far so good